home > Internet > How to reset the counter and settings of a Samsung printer. Why the printer does not print and the red light is on MFP samsung scx 3200 red indicator

How to reset the counter and settings of a Samsung printer. Why the printer does not print and the red light is on MFP samsung scx 3200 red indicator

To effectively use inexpensive cartridges and be able to refill them yourself, you need to bypass the printer menu item that limits the number of sheets printed per refill. This can be done in several ways, depending on the model of the printing device. Reset the counter Samsung printer SCX-3400 and SCX-3200 can be accessed by accessing the menu using a key combination. In earlier printer models Samsung reset can be done by reinstalling the software.

Resetting settings and flashing on older models

The protection system against the use of refilled cartridges on Samsung ML is done only in software. To reset the Samsung ML-1910/ML-1915 printer, you need to replace some of the factory software. For successful flashing you need:

download to computer new version Software for ML-1910/ML-1915;
connect a printer to it (not turning it on);
turn on the device by pressing the button and not releasing it until the red indicator flashes;
release the button;
run the .bat file until FW is completely loaded;
wait for the printer to reboot on its own;
remove or seal the chip on the cartridge.

In the future, when using the reflashed Samsung ML-1910/ML-1915, you should use only cartridges with an isolated chip.

Direct intervention to reset the counter

Resetting the counter on ML-1640/ML-1641 models begins with determining the software version by printing a test page. To do this, press “cancel printing” and hold until both LEDs blink. The value you are looking for is called Engine version. If the value is 1.10.50 and below, you can reconfigure the device.

To do this you need:

disconnect the device from the network;
remove the rear protective panel;
detect microcircuit 93С66;
Having carefully connected the power to the device, but not turning it on, close legs 4 and 3 with a metal object, waiting until only red of the two LEDs on the top panel remains lit;
remove the short circuit, assemble the device, print a test page.

The full ML-1640/ML-1641 test page will be different from what was printed before the procedure. If not, you should try again. In some cases, the ML-1640/ML-1641 counter is reset when pins 1 and 4 are closed.

Reset settings without flashing

The Samsung SCX 3200 (SCX 3205, SCX 3207) printer reset algorithm is simpler. The procedure is carried out without partial disassembly, only by pressing the menu buttons. The keys must be pressed without delay, at equal intervals:

Press the combination ++ stop – – stop stop.
Wait for the letters UC on the display.
Use the “+ –” buttons to change the value to FC.
Click start.
Wait until code 07 appears and press start again.
Wait for the SCX 3200 counter to complete its automatic reset process.

To access the Samsung SCX-3400 printer settings, you need to press the “menu” button ten times. When “service” appears on the display, use the “right” button to scroll through the service to the “reset settings” command and confirm it with the “OK” button. Next, press the “right” button twice. When “all settings” appears, click “OK”.

After several training sessions, reconfiguring the SCX 3200 and other models when refilling the cartridge will take the user just seconds.

Owners of home and office printing equipment quite often encounter problems with the operation of the device: unclear quality, slow performance and complete stoppage of photo printing. Sometimes the problem is that the printer does not print and the red light is on, but it is not clear why this happened. Sometimes you can solve this problem without contacting a service center - after finding out the causes of the fire.

What will we talk about:

Reasons for the red light to come on

Each part of the printer is responsible for certain functions - turning on, printing, scanning (if there is a scanner), etc.

If the printer's red light is on, the problem may be due to:

Paper jam - if the paper is too thin, wrinkled or does not meet the requirements of the device or the printer cannot pick it up.
The cartridge is not inserted correctly.
It is necessary to reset the counter of printed pages (in other words, flash the device).

Another reason for the red light to come on is that the ink in the cartridge is running low. Regardless of which printer model is SCX-3200 or SCX-3205, the methods for solving the problem are the same. Smart Samsung printer manufacturers have protected branded cartridges (which come with the device) with a special chip.

This miniature electronic part protects the part from unprofessional influence and forces printer owners to buy new, expensive toner. But firmware for a branded toner will help save your budget. Often the cause of errors in the operation of printing equipment is a poor connection to the computer (cable, USB input).

If the light is not constantly lit red, but only blinks, there are two reasons for this: 1) the need to refill the toner or completely replace it, 2) printing is carried out in manual feed mode.

In the case when the red color continuously hurts the eyes, the reason may lie not only in the toner, but also in:

The device cover is open.
A critical error related to the device motor (for example, the board burned out).
There is no paper in the tray.

The first and third problems can be solved independently, the second - only in service center. To protect yourself from guessing and know for sure why the red indicator lights up, you need to install on the printer Smart program Panel, which provides information about the amount of ink in the toner and possible problems.

Features of the problem in different models of Samsung printers

The South Korean printer manufacturer Samsung is one of the leaders in the production of office and printing equipment. Each printer model has its own differences in size, color scheme and number of functions performed. But the problems in the operation of the devices are approximately the same. If the red light on the printer is on, then there is no difference - this Samsung model SCX-3200 or Samsung SCX-3205 when solving the problem.

In most cases, the problem is with the toner. After purchasing a new device, it is filled to 35-40 percent, which is enough to print 1000-1500 sheets of paper. Immediately after purchasing the printer, you should take this detail into account and prepare in advance for refueling. You can check the amount of ink in the toner using the diagnostic program.

Ways to solve the problem

At home, in an Internet cafe or in the office of a large company, the following problem may arise: the Samsung printer does not print and the red light is on. In this case, it is necessary to study the instructions for the device and carefully inspect the wires for connecting to the electrical network. Then open the cover, remove and inspect the cartridge and paper tray. If this is not the reason, then you should dig deeper - into the electronic system of the printer.

If the reason for the red indicator to light up is the need to reset the counters, then you need to do this:

Connect the device to the power supply.
Press several buttons in succession as quickly as possible: “+”, “+”, “stop”, “-”, “-”, “stop”, “stop”.
After this, the inscription FC will appear on the device display.
Press the “start” button, after which two numbers will appear – 07.
Then press “start” again, wait a few minutes and the system will reset to zero.

If the printer cartridge was being repaired (the firmware was being updated), then the reason may be due to defects of the technician. Despite the verbal complexity, you can fix the problem yourself. To do this, you need to insert the cartridge into the device and turn on the device. After this it must be initialized. After initialization, you need to remove the part, seal the chip (it must be provided by the master), and get to work.

Often, after updating the firmware, the printer owner discovers a problem - the device does not want to work and is blocked. In this case, the “saving” key combination will be the following, which will change the region: Up(+) Up(+) Stop Down(-) Down(-) Stop Stop. After pressing these buttons, the letter combination “UC” will appear on the display. As soon as these letters become visible, you need to press the “Up (+)” button until the “FC” combination appears. Then you need to press the “start” button and select the region indicated by the numbers “01” or “07”. After such manipulations, the printer will reboot itself and become suitable for printing.

Unacceptable actions when the red light on the printer lights up

So that the Samsung printer after the red button lights up can be useful to the owner after the red indicator lights up, you need to know what not to do in this situation:

Press all the buttons.
Knock on the walls and lid of the device (especially when it is in operation).
Disconnect the device from the power supply without first turning it off using the button.

If the printer lights up red and does not print, then you need to carefully examine all the details and if, after carrying out possible actions, the light on the Samsung does not go out, you need to contact a professional technician. At the service center, professionals may discover the need for toner firmware. In order for the printer to resume its operating functions the first time, you must inform a specialist serial number and firmware version.

This instruction will help you reset the counter for Samsung multifunctional devices, line SCX-3200, SCX-3205, SCX-3205W, SCX-3207 with already changed software or in other words, reflashed, when the printing process is blocked after the next refill of the cartridges used in these models Samsung MLT-104.

If the “status” indicator on the printer panel lights up red and the printer requires replacing the cartridge, you need to reset the toner counter using the following algorithm:

Instructions for resetting the toner counter on Samsung SCX-3200, SCX-3205, SCX-3207 printers

1. Press quickly, without pausing, the following combination of buttons on the printer panel:
+ + stop - - stop stop(2 times “+”, “stop”, 2 times “-”, 2 times “stop”)

2. If you did everything correctly and quickly enough, the letters should appear on the printer display "UC". If it doesn't work the first time, it's okay, try again

3. Button «+» or «-« switch the inscriptions on the display to the value "FC"

4. Press the button "Start"

5. Numbers will appear on the display "07"

6. Press the button again "Start"
After this, the reset process will begin. Wait until the reset is completed and the printer turns off. Now you can turn on the printer and start printing.