Output of diaper Epson SX130, SX125, NX130. Instructions for resetting the RPC (refillable cartridges) of Epson S, SX, B, BX series printers Epson stylus sx130 diaper reset

To reset the waste counter Epson ink SX125 and SX130 program used Adjustment Program ver 1.0.1. Actually, it is intended for ME320 and TX121, but SX125 and SX130 are a blast.

Unfortunately, you cannot download the program from our website.

Operating procedure: We launch the service program for Epson printers ME320, TX121, which is suitable for resetting diapers of many new printers, incl. and S22, SX125, SX130...

IMPORTANT! Do not try other functions other than resetting the diaper if you do not want problems for your printer.

Connect the printer to your computer with a good USB cable. Turn on the printer and run the program.
Select model TX121 for MFP type SX125, SX130 ... or ME320 for S22.
Destination you can choose ESP. Port - auto.
Next, as usual - Particular Adjustment Mode
Select an item Waste Ink Pad Counter and we go into it.
We check the boxes on both counters - Main Pad Counter and FL Box Counter.
Click Initialization.
Turn off the printer so that it remembers the reset.
Let's launch universal utility PrintHelp and check the value of the diaper counters - they should be 0%.

If it is more convenient for you to watch and listen, then how to use this program is shown in this video:

To add this page to your "Favorites" click

Other articles in this section:

If your printing device series Epson Stylus NX, SX, S shows a message that “Some parts of the printer are worn out and it needs to be sent to service center", while all the LEDs on the printer are blinking, most likely this indicates that the resource of the so-called “Pampers” of the printer has been exhausted and needs to be replaced. Usually you can use various programs or utilities that allow you to reset the diaper counter and you can continue printing. But after a large cycle of printed sheets, sooner or later the diaper actually becomes overfilled with ink and it can simply leak out of the printer onto your desktop.

To avoid such trouble, we bring to your attention an article that describes in detail how to output diapers on printers and multifunction devices, on Epson example Stylus NX130, Epson Stylus SX130, Epson Stylus SX125, Epson Stylus S22.

For this we need a rubber tube and a 100 ml container. The pictures show the corners, in principle it is quite possible to do without them, the main thing is that the connections are strong and do not let ink through.

So, open the cover on the back of the MFP or printer; you may need a screwdriver for this. Disconnect the printer's rubber tube that is connected to the diaper and attach it to the tube that will discharge ink into the container. To do this, make two holes in the plug of the ink flask: one for the cable, the second for air outlet.

Next, everything is very simple, insert the end of the rubber tube into the ink container, and close the lid so as not to crush the cable, for free ink output. The waste ink container should be level with the printing device.

When performing all these actions, be extremely careful and do everything wearing protective gloves so as not to get your hands dirty;-)

Relevant for Epson S22, SX125, SX130.

1. Press the "drop" button, the carriage will enter the replacement position;
2. Without removing the cartridge , press the "drop" button again;
3. The carriage will start to run, but the chips will not reset to zero;
4. When the carriage stops, press the drop button again;
5. The carriage will indicate which cartridge has run out and will move to the replacement position;
6. Pull out this cartridge and insert it back;
7. Press the “drop” button, ink pumping will begin, after which the cartridges will be identified!

________________________________________

For printers and MFPs without a drop button.

1. You begin the process of replacing cartridges - from a printer or from a computer, while the carriage with cartridges first shows which cartridges to change, and then moves to the position of replacing cartridges. In order for the carriage to move, you need to click “next” on the printer or computer;
2. When the carriage with cartridges reaches the replacement position - cartridges don't pull it out;
3. The carriage will start to run, but the chips will not reset to zero;
4. When the carriage stops, repeat step 1 again;
5. The carriage will indicate which cartridge has run out and will move to the replacement position;
6. Take this cartridge out and put it back in;
7. Click the "next" button, ink pumping will begin, after which the cartridges will be identified!

For color cartridges you only need to follow steps 1, 5, 6, 7

The procedure for resetting a cartridge causes a feeling of confusion among many Epson printer owners. Although this is not such a difficult process. Since there are several types of refillable cartridges for printing devices from this manufacturer, the process of resetting them can be done in several ways.

If your printer's SCP has a special reset button, simply remove the carriage of the replacement device and press this button without releasing it for 5-7 seconds. If your cartridge is not equipped with such a button, but has two small round contacts on the chip, located at a distance of about a millimeter from each other, the zeroing procedure will be slightly different. Start by removing the slam-shut valve selected for zeroing according to the printer instructions. Then take a flathead screwdriver and short-circuit these contacts.

If the SCP on your printing device does not have a reset button or two contacts on the top of the chip, you can reset it as follows. Remove it from the printer and immediately return it to its place. Thus, zeroing will occur automatically.

Regardless of how you reset the cartridge, the final step should be confirmation of the cartridge replacement process on the printer panel and the refill itself. This will help avoid head congestion, which can occur if the actual ink level in the cartridge runs out before you decide to reset it.

Please note that the reset procedure Epson cartridge will be available only after the printing device itself reports the need to replace the safety valve.