home > Internet > Reset diapers (absorber counter) for Epson Epson S22, SX125, SX130, SX230, SX235, SX240, SX245, SX430, SX435, SX440, SX445. Turning a frog into a princess on the example of Epson SX130 Cancellation of the counter epson stylus sx130

Reset diapers (absorber counter) for Epson Epson S22, SX125, SX130, SX230, SX235, SX240, SX245, SX430, SX435, SX440, SX445. Turning a frog into a princess on the example of Epson SX130 Cancellation of the counter epson stylus sx130

The procedure for resetting the cartridge causes a feeling of confusion for many owners Epson printers. It's not such a difficult process though. Since there are several types of refillable cartridges for printers from this manufacturer, the process of resetting them can be done in several ways.

If your printer's slam-shut has a special reset button, simply pull out the replacement carriage and press this button without releasing for 5-7 seconds. If your cartridge is not equipped with such a button, but has two small round contacts on the chip, spaced about a millimeter apart, the zeroing procedure will be slightly different. Start by removing the slam-shut device selected for reset according to the printer instructions. Then take a flathead screwdriver and close these contacts.

If the PZK on your printer does not have a reset button or two pins on the top of the chip, you can reset it as follows. Remove it from the printer and immediately return it to its place. Thus, zeroing will occur automatically.

Regardless of how you reset the cartridge, the final step should be to confirm the cartridge replacement process on the printer panel and refill itself. This will help avoid head air, which can occur if the actual ink level in the cartridge runs out before you decide to reset it.

Please note that the reset procedure Epson cartridge will be available only after the printing device itself informs about the need to replace the slam-shut.

[yt=Skuoa_brfuI] [yt=Skuoa_brfuI]

Actual for Epson S22, SX125, SX130.

1. Press the "drop" button, the carriage will enter the replacement position;
2. Without removing the cartridge , press the "drop" button again;
3. The carriage will start to run, while the chips will not be reset;
4. When the carriage stops, press the "drop" button again;
5. The carriage will indicate which cartridge has run out and exit to the replacement position;
6. Pull out this cartridge and put it back;
7. Press the "drop" button, ink pumping will begin, after which the cartridges will be recognized!

________________________________________

For printers and MFPs without a drop button.

You start the process of replacing cartridges - from a printer or from a computer, while the carriage with cartridges first shows which cartridges to change, and then it moves to the cartridge replacement position. To move the carriage, you need to press "next" on the printer or computer;
When the cartridge carriage moves to the replacement position, the cartridges do not pull out;
The carriage will start running, while the chips will not be reset;
When the carriage stops, repeat step 1 again;
The carriage will indicate which cartridge has run out and exit to the replacement position;
Take out this cartridge and put it back;
Press the "next" button, ink pumping will begin, after which the cartridges will be recognized!

For color cartridges, you only need to complete steps 1, 5, 6, 7

To reset the counter Epson ink SX125 and SX130 program is used Adjustment Program ver 1.0.1. Actually, it is designed for ME320 and TX121, but SX125 and SX130 folds with a bang.

Unfortunately, it is not possible to download the program from our site.

Operating procedure: We launch the service program for Epson ME320, TX121 printers, which is suitable for resetting the diapers of many new printers, incl. and S22, SX125, SX130...

IMPORTANT! Don't try anything other than resetting the diaper if you don't want your printer in trouble.

Connect the printer to your computer with a good USB cable. Turn on the printer and run the program.
Choose a model TX121 for MFP type SX125, SX130 ... or ME320 for S22.
Destination you can choose ESP. Port - auto.
Further, as usual - Particular Adjustment Mode
Choose an item Waste Ink Pad Counter and we go into it.
We put ticks on both counters - Main Pad Counter and FL Box Counter.
Click initialization.
Turn off the printer so that it remembers the reset.
We launch universal utility PrintHelp and check the value of the diaper counters - they should be 0%.