Cartridge hp 85a ce285a refill. How to refill the HP CE285A cartridge? Detailed instructions! Detailed instructions for refueling HP CE285A

The question of how to refill the HP ce285a cartridge often arises among users of such printing devices. Of course, in the absence of the necessary practical training, it is better to contact a specialist. But the procedure is simple, so you can just use the video on the Internet and the advice of other users.

Procedure preparation

Be sure to stock up on inventory:

• - syringes and needles;
• - napkins or paper towels;
• - alcohol or its solution.

The working surface is pre-lined with paper so as not to stain it with ink. If you decide to lead hp ce285a cartridge, then make sure that you do not need to use a flushing mixture to remove dried particles.

For refilling, using a special drill, under the front panel sticker, the holes through which ink will be supplied are enlarged.

Step-by-step refueling is shown in the figure:

How to carry out the procedure quickly and hassle-free?

When refilling cartridges, be sure to follow the sequence of colors to prevent mixing. The syringe dispenses ink into the ce 285 a cartridge. Do not allow the filler to pour out, and especially its contact with the surface of the device. Excess ink is easily pumped out with a syringe.

Refilling the CE 285 A cartridge ends with the elimination of contaminants, for which alcohol is useful. You can not immediately begin to fully use the device. Need to test the equipment.

To refill the HP ce 285 A cartridge, ink must be purchased at specialized points. Thanks to high-quality filler, you will be able to use the printing device for longer.

The official price of the HP CE285A cartridge exceeds 50% of the cost of new printers designed for this consumable. This is a serious argument in favor of asking the question about his , both through their own efforts and through specialized , since in both cases the level of savings will reach unimaginable proportions.

Count yourself! For a CE285A cartridge, official retailers in Moscow ask for about 5,500 rubles, while our craftsmen will be able to recycle the part for just . However, for those users who want to save even more, we suggest that you read the detailed instructions and figure out how to refill the HP CE285A cartridge with your own hands.

On a note! The CE285A cartridge is compatible with HP LaserJet P1102 / 1102w / M1132 / M1212 / M1214 / M1217 / M1210ser printers.

List of required tools for refilling HP CE285A

To restore the work of the cartridge we mentioned above, you will need a standard set of tools and consumables:

1. Screwdrivers with straight and cross slots.
2. Needle nose pliers or medium size tweezers.
3. Lubricating machine oil.
4. Primary Charge Roll Cleaner (PCR).
5. Compatible toner and chip, last one if needed. More detailed information about resetting or replacing the security chip can be found by going to .

Detailed instructions for refueling HP CE285A

Stage #1. On the right side of the cartridge, unscrew the screw, then removing the corresponding cover. Attention! Be careful not to lose the springs on both sides of the consumable structure. Carefully remove them with needle nose pliers or tweezers.

Stage number 2. Slide the photoconductor part to the left and separate the cartridge into two halves. Remove the drum from the waste bin by gently prying on the gear. Remove the PCR and clean it with a special cleaner.

Stage number 3. Remove the squeegee by unscrewing the two screws, and then clean it of debris. Put a new or polished squeegee back in and remember to apply a thin coat of lubricant.

Stage 4. Install the cleaner-treated VPZ and apply grease to the shaft bearing shaft, and then insert the photoconductor into place as shown in the picture.

Stage number 5. Having unscrewed a couple of screws on the right, remove the toner compartment cover, remove the plastic gears under it. On the reverse side, also unscrew one screw.

Stage number 6. Carefully remove the magnetic shaft. Unscrew the two screws and remove the dosimeter blade. Carefully remove the remnants of the toner powder in the place indicated on the screen!

Stage number 7. Refill the appropriate HP CE285A cartridge slot compatible toner. Tighten the left cover of the consumable with a screw. Install the doctor blade in the same way.

Stage number 8. Insert the magnetic shaft, turn it until you feel a click. Mount the gears and screw on the cover.

Stage number 9. Slide the waste ink powder box into the toner box. Fasten the springs.

Stage 10. Place the special spring on the side cap. Having lifted the springy element of the shutter, install the body part and fix it with a screw. If there is a need to replace the chip - make microcircuits.

This concludes the instructions for refilling the CE285A cartridge. By the way, in order to repeat the above algorithm of actions, it is desirable for the user to have at least minimal experience in servicing office equipment, because the procedure for assembling and disassembling the consumable requires sufficient concentration of attention on the part of the master.

Do-it-yourself refuel HP CE285A or contact Miraxprint service center for help?

Self-filling the CE285A cartridge entails a list of risks and pitfalls that no one notices at first glance. They should include:

1. no guarantee of consumable performance after its recycling;
2. expenses associated with the purchase of toner, special cleaning products and security chips;
3. wasted time and nerves.

This raises the question, is it worth the candle if the HP CE285A can be given to Miraxprint specialists? The cost of refilling this cartridge in our service center will cost ., which is almost 20 times cheaper than buying a new consumable. And favorable conditions , together with the ability to call the master to the specified address will allow you to save a decent amount without leaving your office or home Money, time and nerve cells!

You still do not know how to refill the HP CE285A cartridge? contact us for help by coming to the office or by calling the phone numbers indicated in the header of the site to get qualified advice from professionals!

It happens that you need to refill the cartridge, but it is night outside, and it is not possible to go to the cartridge refilling center. Well, and suddenly you have a toner for your cartridge lying around at home? Therefore, we bring to your attention the instructions for refueling. For those who have already run at least once, it will serve as a reminder (in the form of text). For those who will undertake this for the first time - a more detailed video is attached below!

Before starting refueling laser cartridge hp CE285A at home, cover work surface newspapers, paper or waste oilcloth and place the tools listed in the figure in front of you.

Tools needed to refill the hp CE285A toner cartridge at home

Having prepared all the tools, get to work.

Take the cartridge in your hands and turn it towards you with the side with the drum protection shutter (moving part). Pull back the shutter so that you can see the photoconductor
	Find a small spring on the edge of the cartridge and, picking it up with something sharp, remove it from the mechanism
Remove the two screws that secure the drum cover. Remove the cover
	Grasp the drum gear with your fingers and pull it out of the mechanism. Do not touch the glossy surface of the drum unit with your hands, as toner will stick to your prints later.
Examine the surface of the photoconductor. If it is worn out - replace the photoconductor with a new one, if it is not worn out - quickly remove it to a dark place, as the photoconductor may light up from direct sunlight
	Remove the charge roller from the cartridge and clean it with a dry, soft, lint-free cloth. If you are unable to remove the charge shaft - pick it up by the metal axis with an awl or other sharp object
Now you need to knock out the pins that hold the halves of the cartridge together. The figure shows the outer part of the pin, the rest of its body is located on the inside of the cartridge
	Focusing on the location of the outer part of the pin, push it out from the inside with a screwdriver, awl, knitting needle or other device convenient for you
Pick up the pin that appears outside with platypuses and pull it towards you until the body of the pin comes out completely
	After removing both pins, the cartridge splits into two halves. The left side of the figure shows the waste toner box, the right side shows the new toner box.
Take the waste toner half (the one on the left), unscrew the two screws and remove the squeegee (cleaning blade). Take a vacuum cleaner and vacuum up the waste toner. If you don't have a vacuum cleaner, you can simply turn the drawer upside down and pour the waste toner onto a newspaper.
	Wipe everything thoroughly available parts waste toner box, and then reassemble it in reverse order
Replace the corotron that clips into the waste toner box
	Pick up the compartment for the new toner (the magnetic shaft is located in it) and unscrew the cover from the side where there is no gear. Remove it carefully
Remove the cap that closes the toner tank opening. Hold the magnetic shaft with your finger so that it does not fall out of the mechanism.
	Insert a funnel into the hopper mouth. Shaking the can of toner thoroughly, pour 120-150 grams of toner into the funnel. Don't forget to hold the magnetic shaft
Keeping your finger on the magnetic roller, close the hopper mouth with a stopper and put on the lid. Be careful not to damage the magnetic shaft spring. Screw on the neck cap
	Take the two halves of the cartridge and connect them so that the pin holes line up. Put the pins back in place on both sides
Wipe the charge roller clean and reinstall it. Reinstall the photoconductor: holding it by the gear and twisting it, put it on the metal sleeve. Insert the other side of the photoconductor into the groove. From the end, put on and tighten the drum cover and return the spring to its original position. Put back the curtain
	Pay attention to the end of the cartridge. The metal sleeve must not protrude from the edge of the plastic casing. It should fit snugly into the hole. A protruding sleeve indicates that you have not correctly put the photoconductor on it. The protruding sleeve should be hammered back under the casing with neat, measured movements.
Insert the cartridge into the printer. We print a test page. If the page printed correctly, congratulations! You have just learned how to refill the cartridge yourself!

Refill HP 85A Cartridge (CE285A)! How it works?

In order to provide the highest quality services to our customers, in the round-the-clock service center "MosToner" refilling a laser cartridge HP 85 A (CE285A) produced in just 4 steps:

• STEP #1. Place an order at any time convenient for you
• STEP #2. Free departure of the master within the Moscow Ring Road
• STEP #3. Free cartridge diagnostics with subsequent refilling
• STEP #4. Cash or non-cash payment upon completion of work

On a note! Servicing Cartridges HP at the specialists of the company "MosToner", you save not only your money, but also time. For example, the filling procedure CE285A takes no more than 10 minutes!

Get a discount on refilling HP 85A cartridge (CE285A)

The MostToner SC presents some of the most affordable prices for refilling cartridges in Moscow. However, you can always count on additional discount if you find similar proposal at a lower price.

For regular customers and wholesale customers we have special loyalty programs. For details, please use the form or call the contact phone number.

To receive up-to-date information about current promotional offers, it is not necessary to regularly follow the news on home page site, for this it is enough to subscribe to the newsletter in the corresponding menu at the bottom of the screen.

Also service center MostToner regularly gives promo codes to your customers with individual discounts, with which you can save from a couple of hundred to several thousand rubles, depending on the frequency and cost of orders.

Attention! Promo codes must be entered during checkout as shown in the image.

Instructions for refilling the cartridge HP CE285A

Detailed photo report on refilling the HP CE285A cartridge for laser printers and HP MFP

The HP CE285A Cartridge is compatible with the following HP products:
LaserJet /LJ-P1100ser
LaserJet /LJ-P1101
LaserJet /LJ-P1102
LaserJet /LJ-P1103
LaserJet /LJ-P1104
LaserJet /LJ-P1106
LaserJet /LJ-P1108
LaserJet /LJ-P1109
LaserJet Pro /LJP-M1130ser
LaserJet Pro /LJP-M1132
LaserJet Pro /LJP-M1136
LaserJet Pro /LJP-M1137
LaserJet Pro /LJP-M1210ser
LaserJet Pro /LJP-M1212
LaserJet Pro /LJP-M1214
LaserJet Pro /LJP-M1217 ( The lineup may replenish)

Unscrew the screw from the side and remove the cover

view of the cartridge with the cover removed

We separate the cartridge into two halves (see photo below)

Remove the drum unit to clean the waste toner box

We remove the squeegee by unscrewing two screws. And we remove the processing. After cleaning, you can put everything back in place.

Now you need to clean and refill the toner cartridge. First, remove the magnetic shaft.

To remove the magnetic shaft, you need to unscrew the screw and remove the sidewall.

Carefully remove the sidewall, slightly shaking it.

Now you can remove the magnetic shaft.

We unscrew the two screws to remove the dosing ruler and clean it.

Adhering toner to the ruler must be cleaned with acetone. If the ruler is not cleaned, the print quality of the cartridge will deteriorate with faint streaks. It can also be replaced with a new one.

We will do the same with the magnetic shaft. It also needs to be cleaned up.

Before assembling the toner cartridge again, it must be refilled with new toner.

after refueling and assembly toner cartridge. Turn the magnetic shaft a few turns “away from you” - the toner on it should be distributed evenly.

We assemble the cartridge in the reverse order. After installing the side cover, install the spring as shown in the photo below so that the drum cover can automatically close.