Washing modes in the washing machine indesit. How to turn on the washing machine: instructions for different models The old Indesit model I don’t know how to turn it on
A washing machine is a complex household appliance that requires adherence to certain operating rules. She needs a water supply, a drain system, electricity. Overloading may damage the machine. For such a machine, a special powder marked "Automatic" is required. The washing program must be selected according to the type of fabric. Only after all the nuances are taken into account, you can wash clothes.
Show all
Preparing to start the washing machine
Before you start the washing machine, you need to perform a few simple steps. It is best to find the instructions for it, which describes in detail all the nuances from installation to daily operation.
Water supply
If there is no start-up instruction and you do not know if the machine is ready for use, you need to start by inspecting the hoses. Any washing machine has two of them:
- 1. One supplies water to the machine.
- 2. Another merges it into the sewer after washing.
A hose coming out of the top of the rear wall of the washing machine supplies water. It is connected to a cold water pipe. Often, a tap is placed near the tie-in of the hose to emergency shut off the water in case of malfunctions of the washing machine. Make sure it's open. If there are no markings on it, then just remember where it is. Subsequently, if after pressing the "start" button on the device no water flows into the tank, you will need to turn it (which means that before that it was in the "closed" position).
If the end of the water supply hose is not connected anywhere, look on the cold water pipe for a separate nipple covered with a lid. If available, turn off the water in the apartment (according to the standard, taps are installed next to water meters), remove the plug from the nipple and connect the free end of the hose to the pipe.
After that, open the tap for supplying cold water to the apartment and check the connection for leaks.
It must be tightly twisted so as not to let water through, otherwise it will flood the neighbors below. If the pipes do not have an output end for the hose of the washing machine, then you will have to call specialists to connect. It is not always possible to do this on your own.
Drain
Having dealt with the water supply, you need to inspect the drain hose. Its end should go into the sewer pipe. If no permanent connection has been made, lower the end of the hose into a bathroom or toilet. Complete with a washing machine for such cases, there is a plastic curved plate that is worn on the end of the hose. Without it, the pressure of water draining from the machine will knock the light hose out of the tank.
Electricity
Last action preparatory phase there will be an inspection of the electrical cord, which must be free of damage, creases and bare wires. After making sure that it does not pose a clear threat when used, plug it into an electrical outlet. Now you can start washing.
Luke
Most often there are washing machines with horizontal loading. In this case, the door is located on the front wall and looks like a porthole or a round window.
In order to open the hatch, you need to lightly press on its rim and release. The second option is to feel for the tongue on the right under the handle and, pressing on it, pull the cover towards you.
If there is no hatch on the front wall of the machine, then this is a top-loading washing machine. To load laundry, you need to open the top cover by the handle. Most often, such a hatch device is found in Bosch and Indesit.
A washing machine with a small load is easy to determine. If the width of the machine does not exceed 40 cm, and the drum itself is 15 cm, no more than 3 kg of dirty laundry can be washed at a time. You need to put things in the drum in a straightened form, without tamping. As soon as the space runs out, you must stop downloading.
After finishing, for machines with vertical loading, you need to snap the drum itself, and only then the lid. When properly closed, a characteristic click of a triggered lock will be heard.
Powder
After the laundry is loaded into the drum, it is required to pour the washing powder into a special compartment. On machines with horizontal loading, this is a drawer with three compartments.
On top loaders, the powder tray is on the inside. top cover.
If the laundry is heavily soiled, it is worth choosing modes with a prewash. Then the powder is poured into the compartment marked A (on some models it is marked I). In all other modes, the laundry detergent is poured into compartment B (or II, respectively).
In such machines, only the product marked "Automatic" can be used. Excessive foaming of the hand wash powder can damage the appliance. If capsules are used as a detergent, they must be loaded with the laundry. The washing gel can be poured directly into the drum or tray. The powder is poured only into a special compartment.
The amount of powder depends on the amount of laundry. It is calculated by weight: one tablespoon per 1 kg. For example, a bedding set for a double bed weighs approximately 2000 grams.
Washing program
AT washing machines different manufacturers washing programs have slightly different names, but they perform approximately the same functions. Their main difference is that they are intended for various types things and the process takes place at different temperatures. Most often, programs are indicated near the touch buttons that launch them.
or around a round wheel with a risk, with which you can select the desired washing mode.
In addition, there are often separate extra rinse or spin speed buttons. You can use them only before starting: an already activated washing program cannot be changed.
Starting the washing machine
If everything is done correctly, you can turn on the washing machine. To do this, click on the "Start" button. It looks different, but the designation on it is the same type and it is easy to recognize.
Indesit is a world famous brand of washing machines. The product line includes modern household appliances equipped with a clear interface. Washing modes in washing machine Indesit allows you to choose the optimal program for a particular type of fabric and, thereby, preserve the original appearance clothes.
Basic programs for washing in automatic machines Indesit
The manufacturer on each model made a distinction between basic and additional modes. This allows you to choose a convenient, in time, and correct, for the fabric, program in the washing machine. Due to this, the hostess may not worry that the clothes will shed, stretch or, conversely, decrease in size. Moreover, Indesit has taken care of the proper care of children's things by creating the Indesit washing mode - “hypoallergenic washing”.
The standard programs installed in each model include:
- Cotton.
This program is designed to pre-soak fabrics at a high temperature (90°). However, the drum in this mode should be loaded to the maximum - in this case, washing will be more efficient and economical in terms of electricity consumption. The period of operation of the mode is 2 hours and 51 minutes.
It is noteworthy that on “cotton” you can qualitatively wash greasy towels from the kitchen, napkins, and also remove germs from bath accessories.
Additionally, the program has an additional setting for intensive washing. Unlike the normal mode, there is no soaking procedure and the clothes will be ready to dry in 2 hours and 35 minutes. As a rule, it is used for heavy soiling on tablecloths and bed linen.
And one more sub-mode in cotton is washing under the influence of 40 ° C, i.e. gentle mode, which takes 2 hours and 27 minutes. Recommended for the care of colored items.
- Synthetics.
This program combines two sub-modes. The first washes at a temperature of 60 ° C, which takes 1 hour and 25 minutes in time. The second provides delicate care for materials at a temperature of 40 ° C. Washing of things is carried out in 1 hour and 11 minutes.
Often it is required to fill the drum to 50% of the specified volume.
The maximum load mark is located on the front panel next to the powder loading box. AT various models this parameter is from 2 to 3.5 kg.
- Wool.
The wool mode is intended for clothes made of cashmere and other types of wool, incl. with the addition of acrylic. The program is designed for a temperature regime of 40°C. The laundry will be ready to dry in 55 minutes. The maximum loading of the drum is no more than 1.5 kg. At the same time, the speed in this mode is reduced. However, it is possible to reduce it to the required spin in a manual format.
- Silk.
The program is designed to care for delicate fabrics. For example, tulle, underwear, viscose, silk sheets and pajamas, as well as silk products. The temperature regime does not exceed 30°C and takes less than 60 minutes. The maximum loading of the drum from the specified volume is 1.5 kilograms.
It is noteworthy that there is no spin even with a minimum turnover. To get rid of water on clothes and accessories, it is recommended not to twist the fabric, but to lightly squeeze and blot in a clean towel. Drying of items made of delicate fabrics is carried out at a distance from heating radiators.
In some representatives model range The Indesit Cotton program has identical names. For example, "intensive", "normal", "preliminary" and others.
In the instructions for the modes for each machine, you can find the recommended designations for temperature and spin.
Washing modes on popular Indesit models
The mode of operation in a particular Indesit brand washing machine is a recommendation from the manufacturer, which allows you to save and wash things from various contaminants without damaging the fabric structure. Thus, acting according to the instructions, you can enjoy the thing for a long time.
Special washing modes in popular models:
- Indesit WG1035txc.
In this model, additional modes are provided for each main program. So, "Cotton" allows you to sort clothes for heavy or normal soiling at a temperature of 60 ° C, as well as wash linen from a mixture of synthetics and cotton at maximum exposure.
In "Synthetics" softening of fabrics, shedding clothes and strongly colored things is provided. Additionally, you can set the wash with rinsing, with automatic introduction of emollients and even with a water stop.
- Indesit IWDC 6105.
Non-standard programs in this model include: "Light sport" sports items are washed with high level pollution. As a proper effect, the manufacturer advises to load the drum up to the maximum indicated mark. Recommended means - liquid substances.
"Sports shoes" allows you to gently but effectively wash sneakers, sneakers and other shoes made of woven materials. It is not recommended to wash products made of leather or leatherette. The manufacturer does not recommend washing more than two pairs at a time.
"Quick dry wash" is designed for express washing with a quick dry mode. Cleaning of things is carried out with a low level of pollution. It is noteworthy that the permissible threshold for loading the machine is half a kilogram. The laundry will be ready in a quarter of an hour.
- Indesit WISL 105.
This washing machine has only one additional program"Daily wash at 30 ° C." In this mode, only synthetic materials with a low level of soiling can be washed. The wash cycle is designed for half an hour. This allows the owner to save time and energy costs.
Additionally, the mode allows you to care for different materials loaded in one cycle. The exceptions are silk and woolen products.
Permissible drum loading threshold - 3 kilograms. The manufacturer advises using liquid detergents.
Apart from standard modes, in this model the program "Daily care at a temperature of 30 ° C" is added. The manufacturer has developed a washing cycle in which you can load things up to a volume of 3 kilograms of mixed fabrics. The only exception is silk clothing and wool products. The mode implies a time expenditure of half an hour, which significantly saves electricity consumption and the time of the owner household appliances.
Also, the model is equipped with the “Easy Ironing” function, the admission to which depends on the selected program, the volume of the drum load, the temperature of the water and the environment.
- Indesit WIT 60.
This budget model not equipped with additional special programs. However, the manufacturer has made new feature"Water Stop" The use of advanced functionality depends on several parameters - the volume of the drum when loading, the selected temperature regime of water and in the environment. Details can be found on the official website of the manufacturer.
- Indesit WIUN 102.
In addition to the main programs included in the washing machine, Indesit offers the use of the "Daily Wash Synthetics 30 ° C" mode. The cycle is calculated for half an hour in time with the maximum allowable threshold for loading the drum - 3 kilograms.
From the extended functionality, the manufacturer offers additional functions “Easy ironing” and “stop water”, which change the intensity when a particular program is selected, as well as depending on the temperature effect from the environment.
Whoever installs the washing machine should not rush to load it with laundry and start the wash cycle immediately after that. First you need to carefully check whether everything was done correctly. How exactly such manipulations are performed, some advice from professionals will tell you.
So, first of all, it is recommended to study the instructions that come with the device. Even if a person already has experience using automatic washing machines, it is important for him to remember: each of their brands and models may have their own characteristics. They will certainly be mentioned in the manual.
When a careful reading of the instruction manual is worth proceeding to some practical steps. First of all, it is not a sin to make sure that the so-called shipping bolts are removed from the machine. Manufacturers usually screw them on the back of the instrument. Such bolts are needed so that the drum of this household appliance is fixed during transportation.
However, of course, after installing the machine and before its first start-up, they must be unscrewed. Otherwise, washing will fail. Moreover, when starting up with transport bolts not unscrewed, the device can easily break down, and it is possible that a lot of money will be spent on repairing it. The holes remaining after unscrewing these parts must certainly be closed with special plugs, usually attached to the machine.
The next step should be to check the connection of the device to the mains, as well as to the sewerage and water supply. In the case of the last two, it is important not only to confirm for yourself the fact of connecting the drain and water intake holes to the appropriate communications, but also to make sure that everything was sufficiently sealed. After all, if there are gaps at the connection point of the necessary hoses and pipes, regular leaks cannot be avoided during the operation of the device. Special sealing threads, clamps and other similar means will help to cope with a similar problem.
Washing will not work if the tap in the inlet hose is turned off. You also need to make sure that there are no such difficulties - as well as that there are no other obstacles in the way of water into the washing machine.
It is important to make sure that the instrument is level in all planes and placed on a sufficiently stable base. Concrete and well-laid ceramic tiles are considered ideal in this regard. A wooden floor, linoleum and rugs as a base lead to an undesirable effect - vibration of the machine during its operation. A special rubber mat as a stand will help to change the situation in this regard - it will give the device stability.
It is advisable to know in advance what the hardness of the water supplied to the dwelling is. Then it will be possible to purchase a suitable washing powder for the machine and more accurately choose its dosage for washing. By the way, in any case, you should not pour more than 100 grams.
When loading dirty things into the machine, you must not exceed the allowable load volume (it is usually indicated in the instructions). Otherwise, the service life of the device can be greatly reduced due to excessive load on it. It’s better to break the amount of laundry into two washes, sorting it out by color and type of fabric.
It remains only to choose desired program. For some models of machines, it will also be necessary to additionally set the temperature or other parameters (number of revolutions, etc.). After that, after closing the door of the device, press its start button.
At the end of the wash, immediately remove the laundry from the drum. Its long stay there can lead to the formation of mold due to excess moisture. By the way, just for this reason, it is necessary to keep the door of the machine open when the washing is not in progress - so that the excess liquid evaporates.
I draw your attention to the fact that if you incorrectly connect your washing machine to the same water supply or sewage system, then the washing machine will quite possibly work with glitches. When you bought the SMA and brought it home, the box should also contain a manual, this is not just a piece of paper or a beautiful magazine, the correct operation of the washing machine depends on this thing. For your information, when using this technique, there are many nuances that simply cannot be ignored. Often people come to my workshop who did not even bother to open and read at least the contents of this book, but are already running to repair their newly purchased equipment. The main mistake is the incorrect connection of the drain hose, I will get into this a little later and in more detail, and now I will tell you one case that happened just the other day. It will be about connecting the washing machine to electricity. In general, they brought an Indesit washing machine to my workshop, I don’t remember which model, it doesn’t really matter, it’s important that I have it, it worked like a clock, but as soon as the client took it home, it stopped working. At my request, the owner of the machine measured the voltage, it turned out to be 230 volts and everything seems to be fine, but the machine does not work. In view of the scandalous situation, I myself went to the place, the first thing I saw was that the SM was connected through a carrier, when I began to explain to customers that this was not possible, they began to look at me with bulging eyes. Here I would like to clarify that the heater on the washing machine consumes about 2 kW, plus the machine itself another 0.5 kW, and the carrying is designed for 1 kW. In general, I turned on the car, waited for the heating element to work and picked up the carrying wire, it turned out to be so hot that it was very difficult to hold it in my hands, the owners were shocked by this trick, but the tricks did not end there. In addition, I took a multimeter and measured the voltage when the washing machine was running and the heating element was heating the water, that is, at maximum load. There were 170 volts in the carrier. The end of the story was like this, they called an electrician, he ran a direct wire to the place where the SMA stands, and also unsealed the meter, since the electricity went fine before it, and after it there was a huge loss. The whole problem arose due to the fact that the wire entry into the meter was aluminum and it simply oxidized. The moral of that fable is that before you run to the workshop, you need to check the electrical network in your home well.
How to connect the Indesit washing machine to the sewer
It doesn't matter what kind of CMA download you have, whether it's vertical or horizontal, it connects the same way. Another thing is important here, that the Indesit washing machine has one feature that a simple user does not even know about, but the masters know and are silent. We are talking about the troubleshooting mode, it consists in the fact that the SM, before starting washing, checks the main components, that is, turns on the valve for a few seconds, then turns on the pump for the same period of time and only after the pump is turned off, after about 7 seconds 10 starts pouring water, thus starting the washing cycle. Now let's see what happens when you press the start button, that is, run the program. For a few seconds, the water inlet valve is turned on, that is, the washing machine is filled with about 3-4 liters, it depends on the pressure. After the water is poured into the tank, the pump turns on, it does not work for long, something like 4-5 seconds, but during this period of time it starts throwing water into the sewer and here miracles begin, or rather a siphon appears, thanks to which, after turn off the drain pump, water continues to flow into the sewer pipe. Then the brains give a signal to start washing, that is, the valve opens and water begins to fill in, and this happens despite the fact that the water that remained after the diagnosis has not been drained from the tank. The result is self-draining. In each instruction manual it is written that the water drain hose must be raised by 70 80 cm. I can add on my own that I usually stick to the other one, when I install a washing machine for someone, I do this. I measure 5 cm down from the top cover of the washer and to such a height, hang the drain hose, I clearly indicated this in the photo
Watch the video. Why does the Indesit washing machine constantly drain water
How to level a washing machine
Everything is simple here, on any modern SMA there are adjusting legs. It is better to level the machine with a slight tilt back, this is necessary so that water does not flow from under the powder container, in addition, it seems to me that the washing machine in this position is much more stable. I would also like to comment on one question that I am often asked on my youtube channel and in the workshop
We bought an Indesit washing machine, we were happy until the first spin. The fact is that when the washing machine went to spin, it was a little scared at first, after which the vibration began to intensify, as a result, it began to jump all over the bathroom, we urgently had to turn it off. When called to service center, we were simply sent and told to read the instruction manual, in which, in principle, nothing is written
Now let's see where the washing machine is, as I understand it, we are talking about the bathroom and for sure there are tiles in it, this is the reason that the washing machine started jumping. First of all, in this case, you need to go to the store and buy a rubber mat and you don’t need to tell me here that the washer legs are made of rubber, no matter what they are made of, but by placing a rubber mat, you will not only get rid of what SM walks where she wants, and also from excessive vibration. Believe me, it helps in the vast majority of cases.
Which washing mode to choose on the Indesit washing machine
On the powder container, all washing modes are indicated, usually the temperature that is recommended for a particular wash is also written there. Here it is necessary to take into account that it is in Indesit, in some modes, that there is such a function as a stop with water. Now I will dwell on this miracle in more detail. In general, the following happens, you choose the cycle you need, set the temperature you need, the machine erases everything as it should, but when it reaches the spin cycle, it does not wring out, moreover, there is a lot of water left in the tank. Here, people in a panic begin to run to the workshop, and when you ask them what position they washed on, the answer is born like this. After not a long explanation, the person begins to ask, she fucking need him. Only the manufacturer can give an answer to this question, and I can only suggest on what modes our hostesses wash the most.
- Main wash- Synthetics at 40-60 degrees, the cycle lasts from 1:10 to 1:40, depending on the selected temperature. In principle, any laundry is washed
- Daily- As in previous paragraph You can wash any clothes. It lasts about an hour
- Wool- By its name it is already clear what needs to be washed here, washing is designed for 50-60 minutes
- Cotton- The longest cycle, provides for washing at 90 degrees, which I do not recommend doing, I will explain why below. The process takes from 2 to 3 hours, depending on the selected temperature.
- Rinsing- usually takes two rinse cycles, lasts about 15-20 minutes
I have listed the main washings on which our hostesses wash, of course there are additional functions, but as practice shows, very rarely someone uses them, with the possible exception of the "Time Reduction" button. Since the article is already very long, I can’t tell you in detail about each additional function and about each wash cycle, below you will see links where you can download instructions for almost every model of the Indesit washing machine, and now let’s talk about how to use your washer
Proper operation of the washing machine Indesit
In this paragraph, I want to list what not to do and what should be done during the operation of this technique. Many argue with me about the temperature regime, and there are also questions about the spin cycle. I will try to clarify something, and I will give some recommendations that can extend the life of your SMA
- Wash as little as possible and at a temperature above 70 degrees. The higher the temperature, the more scale on the heating element and in the tank of the washing machine. There is a relay on the control module that controls the process of turning the heating element on and off, it is the relay that often fails, since a large current constantly passes through it, by the way, the heating element itself is not happy with permanent job. On the this moment tanks on Indesit are made of carbolite, which do not tolerate high temperatures very well. In addition, when washing at a high temperature, there is a serious load on the power grid in your apartment or house.
- After washing, leave the hatch door ajar, also open the powder container a little
- The spin speed should not exceed 800 rpm, this will extend the life of the oil seal and bearings, if it is possible to wring at lower speeds, then do not hesitate to do so. It is important to understand here that the difference between 600 and 800 will not be very visible, but for the machine you will save a good resource
- Do not use cheap powders, they contain some kind of alkali that corrode the silumin crosses on the drum
- Be sure to put a rubber mat under the washing machine, this will reduce vibration and your washing machine will not walk where it wants to. Of course, this should be done only when SM has a habit of coming to greet you from the bathroom to the kitchen.
- Run a separate powerful outlet for the washing machine, I already wrote above that the washing machine consumes about 2.5 kW
- Drain hose, raise almost to the level of the top cover of the washing machine, this will help to avoid self-draining
Download the instruction manual for the washing machine Indesit
Below you can download about 100 instruction manuals for Indesit washing machines. I draw your attention to the fact that the entire manual is uploaded to Yandex disk. If you live in Ukraine, then I advise you to install a Yandex browser or Opera browser with VPN support on your computer, there are a lot of instructions and it is very difficult to transfer them from one file sharing service to another, everything is checked by an antivirus. The entire manual is freely available, that is, you don’t have to pay for it and send some kind of left sms. I won’t explain how to download a disk from Yandex, I think you are adults and you know how this is done, there is nothing complicated here.
- Download manual washing machine indesit_isl_60_v_ex_
- Download manual washing machine Indesit_IWB_6085
- Download manual washing machine Indesit_IWB_6105
- Download manual washing machine Indesit_IWC_5083
- Download manual washing machine Indesit_IWC_6105
- Download manual washing machine Indesit_IWDC_6105
- Download manual washing machine Indesit_IWDC_7105
- Download manual washing machine Indesit_IWD_5085
- Download manual washing machine Indesit_IWD_5105
- Download manual washing machine Indesit_IWE_6105
- Download manual washing machine indesit_iwsb_5085_cis_
- Download manual washing machine indesit_iwsb_5085_cis__1
- Download manual washing machine Indesit_IWSB_5105
- Download manual washing machine indesit_IWSC-5105
- Download manual washing machine Indesit_IWSD_5085
- Download manual washing machine Indesit_IWSD_5105
- Download manual washing machine indesit_iwub_4105_cis_
- Download manual washing machine Indesit_IWUC_4085
- Download manual washing machine Indesit_IWUC_4105
- Download manual washing machine Indesit_IWUD_4085
- Download manual washing machine Indesit_IWUD_4105
- Download manual washing machine Indesit_IWUE_4105
- Download manual washing machine indesit_maxi_6_kg_wixl_105_ex_
- Download manual washing machine Indesit_PWC_7104_S
- Download manual washing machine Indesit_PWC_7104_W
- Download manual washing machine Indesit_PWC_7105_W
- Download manual washing machine Indesit_PWC_7108_S
- Download manual washing machine Indesit_PWC_7128_S
- Download manual washing machine Indesit_PWDE_7125_S
- Download manual washing machine Indesit_PWE_7104_S
- Download manual washing machine Indesit_PWE_7104_W
- Download manual washing machine Indesit_PWE_7107_S
- Download manual washing machine Indesit_PWE_7108_S
- Download manual washing machine Indesit_PWE_81472_S
- Download manual washing machine Indesit_PWE_8148_S
- Download manual washing machine Indesit_PWSC_5104_W
- Download manual washing machine Indesit_PWSC_5105_W
- Download manual washing machine Indesit_PWSC_6107_S
- Download manual washing machine Indesit_PWSC_6108_S
- Download manual washing machine Indesit_PWSE_6104_S
- Download manual washing machine Indesit_PWSE_6104_W
- Download manual washing machine Indesit_PWSE_6107_S
- Download manual washing machine Indesit_PWSE_6108
- Download manual washing machine Indesit_PWSE_6127_S
- Download manual washing machine Indesit_PWSE_6128_S
- Download manual washing machine Indesit_SISL_106
- Download manual washing machine Indesit_SISL_106_S
- Download manual washing machine Indesit_SISL_129
- Download manual washing machine Indesit_SISL_129_S
- Download manual washing machine Indesit_SIXL_106
- Download manual washing machine Indesit_SIXL_106_S
- Download manual washing machine Indesit_SIXL_126
- Download manual washing machine Indesit_SIXL_129
Turn on Indesit, LG, Bosch equipment and start the program at a certain temperature mode by pressing a button after installing new equipment on a solid and even base. Before turning on the washing machine in the network, you must carefully read the instructions. Each equipment is accompanied by its own technical documentation, and you need to read it very carefully. The manufacturer, referring to the instructions, gives the necessary and very helpful tips, which will bring results both when the device is turned on and when used correctly. Connect machines of different brands in different ways in accordance with the manufacturer's recommendations. Each manufacturer provides the buyer with equipment with universal special functions.
The device, freed from packaging and transport fasteners, is installed in a pre-prepared place. Only a special rug can be placed under the electrical unit, which is aimed at reducing the intensity of vibrations when the device is turned on. Adjusted legs of the equipment allow you to achieve the necessary stability at the time of operation of the device.
The construction level will help to check the perfectly even installation of Indesit and other models. After that, to fully connect the machine, you should connect the device to utilities:
- Power supply network.
- Plumbing and sewerage.
- To connect the machine to the network, use special sockets with an RCD and a separate machine.
Correct actions when turning on the unit
It is necessary to turn on the washing machine in the mains, open the water tap. Liquid is not supplied to the unit in only one case - when operating in the spin mode, it can be turned on with the corresponding button on the control panel or by turning the lever to the desired pattern. When carrying out a test wash on a new machine, do not put laundry in the drum. Close the hatch well; if it is loose, the machine will not start working.
Add detergent, bleach, conditioner to the container. It is necessary to constantly monitor the volume of the loaded powder. Do not add more than one hundred grams, even when a large amount of washing is planned. After that, it is recommended to start the Indesit machine in the workflow.
Start washing
Each washing machine has a different control panel. On modern models, electronic control units are installed, there are no levers. On such a panel, when choosing a washing mode, you need to press the button. Before selecting the desired washing mode, it is forbidden to press the "Start" or "Start" button. Peculiarities different modes washing are indicated in the relevant sections of the instructions for the appliance.
Outdated models of washing equipment have only a certain program for washing, but in modern appliances you can perfectly set the parameters for washing clothes for a particular type. Now you need to select a program, set the number of revolutions for spinning and press "Start" - the machine is included in the workflow.
Preparation for work
There are a few preparatory steps that need to be taken to carry out the wash:
- Plug the machine into a socket.
- Prepare laundry to load into the drum. Modern washing machines have different drum sizes.
- Sort the laundry, fold white and light-colored fabrics separately from dark and colored fabrics.
- Calculate the load of things for equipment Indesit, Lg, Bosch, Ariston, Vestel Aura, Zanussi, Ardo, Beko, Candy.
- The number of clothes to be loaded must correspond to the nominal value of the machine for which the calculation is made. It is recommended to select things for washing from the fabric of the same name.
It is necessary to load the powder, observing the dosage indicated on the package, into a special container, which consists of three compartments:
- The left tray is reserved for the main wash.
- For preliminary - use the right compartment.
- Under the conditioner the average tray is intended.
This is how compartments are distributed in all brands of washing machines.
Loaded detergent volume
The manufacturer of the Zanussi model depicts a memo on the purpose of its compartments on the front of the tray. Other models are labeled in the user manual, which includes complete guide machine control. Do not load more detergents than recommended for each model separately. This can negatively affect the result of washing.
The use of washing powder in excess doses can lead to:
- To traces and stains on the fabric of clothing.
- Incomplete flushing of the tray, which leads to clogging.
- The appearance of an unpleasant odor from the drum.
Dependence of the washing result
Each package with detergent is provided with recommendations from the manufacturer on how and in what quantities to use it in washing machines of different brands. When pouring powder into a special tray, you must consider:
- What condition is the laundry in, the degree of soiling, the presence of the number of stains. To remove stains, it is sometimes necessary to use stain removers.
- The quality of the wash depends on the hardness of the water, which reduces foaming, which affects the result of the wash. For hard water, it is recommended to add two tablespoons baking soda to soften water. This will help the powder to fully dissolve in the liquid.
- The amount of soiled laundry for which the powder volume is calculated.
- The rate of water consumed by the technique per wash, which depends on the mode and type of fabric.
Water consumption per cycle
The amount of liquid used in different machines may differ. This is influenced by the capacity of the tank and the availability of programs that washing equipment has. The average figure of a standard machine with a drum load of seven kilograms requires up to sixty liters of water. The norms for each type of equipment are usually contained in the specific instructions for the model.
Washing machines that have a laundry weighing function can be guided by the actual weight of the laundry. When washing, the technician will weigh things and fill the drum with liquid by weight.
Verified information shows that for machine washable laundry with medium soiling, one tablespoon is required, this equates to 25 g of powder. When washing four kilograms of dry clothes, you need to add one hundred grams of the product.
