home > Internet > Disassemble the washing machine heater. How to replace the ten in the lg washing machine - instructions

Disassemble the washing machine heater. How to replace the ten in the lg washing machine - instructions

The machine stopped heating water, but are all programs set correctly? This means that the heating element in the washing machine needs to be replaced. We will describe in detail the process of dismantling and installing a new heating element and share some helpful tips.

Operation of heating elements: here you can clearly see how the service life affects the condition of the heating element.

TEN device and signs of its breakdown

Before replacing the heating element in a washing machine, it is recommended that you familiarize yourself with the principle of its operation. A heating element is a heater whose task is to heat the water in the tank. The main part of modern heating elements is a tube. Inside it runs a spiral, which is separated from the outer walls of the tube by a dielectric material. The heater breaks more often than other elements due to the fact that this spiral constantly cools and heats up. After losing its properties, it fails. Often this is due to the formation of plaque on the heater tubes. Therefore, the main sign of damage is a thick layer of plaque.

To extend the life of the heating element, it is recommended to clean it every 3-4 months.

Understand that the heating element needs to be replaced washing machine, it is possible on another basis - the water in the barrel stops heating. Sometimes the reason for the lack of hot water is an incorrectly set washing program. If all settings are set correctly, then you can immediately proceed to replacing the heating element.

Also, the reason for the lack of hot water may be a non-working programmer or water heating sensor. It is better to entrust the replacement of these elements to professional repairmen. In any case, after dismantling the heater, you will understand whether it is the reason for the lack of hot water in the machine or not.

What is needed for replacement?

However, before starting work on the replacement, it is worth arming yourself with the following parts and tools:

New TEN. You can buy it at the manufacturer's service center (or get it for free under warranty). We do not recommend buying a used part, because after a while you will have to replace it again;
A set of screwdrivers (usually a slotted screwdriver is enough);
A set of wrenches and tubular wrenches;
Rubber mallet;
Adhesive sealant (if a used heating element is used for replacement).

Step 1 - find the heating element in your model

To get to the heating element, you need to carry out a partial analysis. Each washing machine has differences in its design: for some models, the heating element is located on the front of the case, while for others it is on the back. In order not to waste time on the lengthy dismantling of both covers, you need to decide which of them is behind the heater:

If the back wall is large and has a removable design, most likely the heating element is installed behind it.
If the back wall does not look voluminous, and at the same time you do not see obvious fasteners, then the heating element is located at the bottom of the front wall.

We dismantled the cover, now we need to find the heating element. It is located inside the tank, only terminals with wires can be seen from the outside. The following photo will help you find the heating element:

Disconnect the wiring and check if the heater works or not. This can be done using a regular tester. Fears were confirmed, and it does not work? Then we proceed to the replacement.

Step 2 - remove the non-working part

You have prepared a new replacement part. Now you can start dismantling.

IMPORTANT: There must be no water in the tank. To drain it, you need to unscrew the drain filter.

Now we take a tubular type wrench and remove the central nut - it is indicated by the number "1" in the photo.

After removing the nut, it is necessary to drown the studs (2) inside. A wrench handle, a screwdriver or a rubber hammer will help here - press the pin so that it goes inside the heater.

The fasteners have been removed, so it remains to remove the heating element, which is tightly seated on a rubber gasket . In order to loosen the seal, it is necessary to pry the heating element with a slotted screwdriver. The photo above shows where you need to start getting the part. Remember in what position the heating element was installed. Remove the heater carefully, using a slotted screwdriver from different sides.

Useful advice! There are a lot of wires with which the heating element is connected to the washing machine, so you can easily forget their original location. Before dismantling, take a picture of the assembly on your phone or camera - this will guarantee that the wires will be connected in right order.

Step 3 - Installing the New Item

The main part of the work is done - we removed the non-working part. Now we take a new heater and install it in the mounting hole. Here, too, the help of a screwdriver may come in handy, since the element enters tightly due to the rubber seal. Make sure that the part is level - there should be no offsets or distortions. The replacement of the heating element of the washing machine is almost complete - it remains to install the fasteners. To do this, we wind the mount on the hairpin .

Tighten the pin carefully: if you push it, the heating element may fall into the drum. We remember how the wires were attached and put them in their place. It remains to assemble the back wall, and this replacement can be completed.

Important! Some masters who specialize in repairing washing machines advise putting the heating element on a sealant to prevent water leakage. If you purchased a new part and installed it correctly, then the heating element will “sit” tightly even without the use of glue.

It is recommended to immediately check the operation of the new heating element. To do this, you need to start the wash, setting at least 50 degrees. Wait 15-20 minutes and then touch the sunroof. If its glass is warm, then the washing machine is working properly.

Video: how to change the heating element?

In the following video, the home master will clearly show how to replace the heating element in the washing machine, regardless of its model and manufacturer:

Now you know how to replace the heating element in the washing machine. It is recommended to take on a DIY replacement if you have experience in repair household appliances. Follow all the steps from the instructions carefully, as the wires and terminals are fragile elements. Do not forget to check the heating element every 3-4 months. To consolidate the information received, we recommend watching the video, which shows the replacement of the heating element of the washing machine.

In contact with

The heating element is a heating element that provides heating of water to the required temperature during washing. It is located at the bottom of the device, and due to various circumstances, it can fail, especially with poor-quality water and active use at the maximum washing temperature. Replacing the heating element is easy to do on your own, we will talk about this in the material, give recommendations and valuable advice.

How do you know what needs to be replaced?

To identify a malfunction of the heating element, you need to make sure that the water is not actually heated. To do this, 15 minutes after starting the wash, touch the door with your hand, and if it is cold, this indicates a malfunction of the heating element. This is the only visible sign by which the user can independently identify the absence of heating.

Many models of washing machines have a self-diagnosis system that displays an error code when a malfunction is detected. Error coding different manufacturers is different, so to decrypt the code, you will need to read the instructions for your model of washing machine.

The reasons for the failure of the heating element can be the following:

violation of the integrity of the wiring, as a result of which the heating element does not receive signals about the start of operation and the need for heating;
burnout of the heating element, which requires immediate replacement;
failure of the thermostat responsible for determining the water temperature;
accumulation of a thick layer of scale and salt deposits, which significantly reduces the thermal conductivity of the metal. The heating element cannot give off the necessary heat and heat the water to the specified temperature. Then more electricity is used for heating, as a result of overvoltage, the heating element burns out.

Where is TEN located?

Often users face difficulties in locating the location of the heating element. AT different models access to the heating element is provided through the rear or front panel. To find out the location of the part in your device, read the instructions or inspect the washing machine.

Inspect first back panel, and if the removable part is large enough, most likely, the heating element is located there. If only a small cover is removed from the back, then try to look for the heating element under the front cover.

The rear location of the heating element is typical for Zanussi, Candy, Hotpoint Ariston, Indesit, Ardo and Electrolux brands. Manufacturers Bosch and Samsung in most models have a heating element under the front panel. In a top-loading technique, the side wall must be unscrewed to provide access to the element.

Training

Before you start unwinding the case and replacing the part, you need to prepare the tools and components for replacement.

Washing machine repairs are best left to the professionals!

We present you our unique catalog of private craftsmen and service centers -

Select your city and master in the filter: by rating, reviews, price!

Before starting repair work, completely disconnect the washing machine from the mains, and also disconnect the hoses for supplying and draining water. For safety, you can drain the remaining water from the tank so that, if necessary, you can put the unit on its side or tilt it and avoid leaks and short circuits.

What will be required?

Required tools:

Phillips and flat screwdrivers;
lubricant;
multimeter;
socket head 8 and ratchet wrench.

If the equipment is still under warranty, do not repair it yourself, it is better to contact service center, where, according to the warranty card, the replacement will be performed free of charge.

Step-by-step instructions for removing the heating element

Initially, check that the equipment is disconnected from communications and completely drain the water from the tank through the emergency hose. Only after these manipulations proceed to replace the heating element:

unscrew the bolts of the back cover and find the heating element. It is easy to find it, because the shank is in the visible part of the body;
disconnect wiring;
unscrew the nut in the middle, insert the stud inward by pressing on it with force or by tapping with a hammer;
using a knife or screwdriver, carefully pick up and pull out the heating element from the tank;
then you need to check the performance of the element using the video instruction.

How to choose a new heating element, what you should pay attention to

To choose a suitable heating element that will last a long time and will not fail, it is necessary to be guided by certain selection criteria.

Having pulled the element out of the washing machine, measure its working length from the metal base to the end, also determine the indicated power consumption figure and find the hole for the temperature sensor. The length of the heating elements varies within 150-310 mm, the power is in the range of 1600-2050 W, in some models it reaches 3000 W. If your unit has a kink element, the angle and location of the kink must be considered.

The best solution for purchasing a similar item would be to remove it and compare the parameters directly in the store. Usually a consultant can help with the choice, who will select a completely identical heating element in the warehouse for specific model. If the element has a numerical or letter marking, be guided by it.

Washing machine repairs are best left to the professionals!

We present you our unique catalog of private craftsmen and service centers -

Select your city and master in the filter: by rating, reviews, price!

When buying in online stores, be guided by the cost and do not take cheap options, since such fakes will not last long and will soon require a new replacement.

Step-by-step instructions for installing a heating element

To install a new element, follow the following sequence of actions:

insert the new heating element into the niche and check that it is firmly in place and does not stagger. It is necessary to ensure tight fixation without distortions and gaps;
holding the element, tighten the nut until it stops, but without strong effort, so as not to squeeze out the element;
attach the wires and terminals to the shank in their original places;
turn on the test washing program with heating up to 60 degrees. If the water is heating (this can be checked by placing your hand on the door 10-15 minutes after the start of washing), then fix the back panel and twist the case.

During installation new part perform the actions carefully, check the exact hit of the heating element in the mounts. When not correct installation it may be located above the prescribed level, and during the washing process there will be friction against the drum, which will lead to serious malfunctions of all elements of the device.

Some professional craftsmen recommend securing the position of the heating element with sealant to prevent leaks. However, we note that with proper installation and tight fit, leakage should be excluded without the use of sealant.

Checking work

After installing a new heating element, you need to make sure that there are no leaks and that the heating is correct in the washing mode. To do this, run the test program and check that the heating element heats the water to the required temperature without delay.

Let's also consider how to check the technical parameters of the heating element and what values \u200b\u200bare considered the norm. You can carry out the procedure using a multimeter.

The standard indicators of the heating element vary within 20-40 ohms, based on the declared power of the equipment. AT powerful models resistance can reach 60 ohms. When measuring, if the device shows less than 20 ohms, this always indicates a breakdown and the need to replace a worn or burned out element.

To check with a multimeter, disconnect the equipment from electricity, disconnect all wires from the element. Measuring device connect to the terminals of the heating element, and check the value shown with the standard values.

How to extend the life of the heating element?

To ensure a long service life of the heating element, follow the recommendations:

in order to avoid salt deposits and scale formation, regularly carry out preventive measures, cleaning with citric acid or special products. At standard use cleaning is carried out every 4-6 months, with daily washing, clean every few months;

use a voltage stabilizer to protect equipment from burnout during power surges;
pay attention to non-standard sounds and vibrations, because in advanced cases, the heating element may hit the body. Sometimes you may feel an electric shock when you touch the case.

Possible malfunctions and solutions

If the heating element has stopped heating water, this may be facilitated by malfunctions that can be eliminated on your own or by contacting a service center:

part closure or break. In this case, the remaining components and blocks of the washing machine may burn out, so you must immediately disconnect the equipment from the network and contact a service center to avoid the need for costly overhauls;
heater circuit failure. In this case, the heating of the water is carried out for a longer time or a hang is observed during the washing process. Requires replacement of the heating element;
malfunction of the pressure switch, which is responsible for transmitting a signal about the water level. If the sensor is contaminated with scale and the heating signal does not come from it, then it is necessary to replace it.

The video shows detailed instruction how to pull out the old heater and install a new one in its place.

Using our step by step instructions and recommendations, you can at home identify a problem with the heating element and replace it with a minimum set of tools. When buying a heating element, choose an identical heater that fits your device model.

Reading 6 min. Views 12

Where is TEN
Teng front
Ten behind
Video

Teng serves to heat the liquid. If we talk about a washing machine, then the washing process takes place at a certain temperature, which you set on the instrument panel. It is the heater that heats the water in the washing machine to the desired temperature.

Due to the fact that water can be hard and with impurities, when heated, scale forms, which over time, if the heating element is not cleaned, leads to a breakdown of the device. It can fail for other reasons as well. Therefore, if you notice that the water in the washing machine is not heated, the heating element may have broken. This needs to be checked and, if necessary, buy another. True, you need to know how to replace a heating element in a washing machine without the help of specialists. Where is it located and how can I check if it works or is broken? Let's find out.

Where is TEN

To replace this element, you need to know where it is located. Naturally, there are many different washing machines, but, as a rule, the heating element is located at the bottom of the tank. But how to get to it already depends on the model. On some machines it is behind the front panel, on others it is behind the back cover. Sometimes it can be on the side of machines with side loading.

Ten behind the front panel

To determine exactly where it is located for you, first remove back cover and look under the tank. It is easier to unscrew, so it will be the first. If the heating element is located there - excellent, you can proceed to its removal. When it is not there, you need to unscrew the front panel. We can say that the first stage was successful. It remains only to take it out, check it, and, if necessary, replace it. Let's see how to do it step by step. And to simplify your task, the article will describe two methods for disassembling cars. The first is when the ten is in front, the other is when it is located behind.

Here are some rules to follow, regardless of the brand of the device:

If the machine is connected to the mains, be sure to turn it off by pulling the plug from the socket.
Drain all the water completely, use the drain filter to do this, or drain the water through the hose, lowering it below the level of the machine.
Some water may remain, so have a basin, rag, or mop handy.

May also be located behind the rear panel

This completes the preparatory work. For further work you will need:

Screwdriver.
Open-end wrench or socket wrench 8 or 10.

That's all, as you can see, special specialized tools are not required, due to the simplicity of work, everything can be done by hand.

Teng front

As we said earlier, often in all models the heater is located behind the back cover. But if you have a Bosh, LG or Samsung device, behind the back panel you will find only a drive belt that attaches to the motor. The heater itself is located in front, under the drum. So, let's consider the work in stages.

Removing the top panel

First, you need to remove the top cover. To do this, unscrew the two screws that secure the cover. They are at the back. They can be a Phillips screwdriver, flat or Torx. After unscrewing them, pull the cover back and remove it.
Then take out the detergent drawer. In its place there will also be 2 self-tapping screws that need to be unscrewed. There is a latch on the back of the front panel that needs to be pushed back. Then she takes off.
Remove the steel hoop and rubber seal The next step is to remove the steel hoop that holds the seal (rubber cuff) on the loading hatch. This ring is pulled together by a conventional wire spring. You need to stretch the spring and remove the hoop from the seal.
Now remove the rubber seal.
There should be self-tapping screws on the front panel, bottom or front, which also need to be unscrewed. It remains to remove the cover. It can be attached with additional clips. Therefore, the cover must be pulled forward a little and lowered down.
Near the hatch there is a door blocker. From it you need to disconnect the wires. Now you can remove the panel and go to the heater itself.
Contacts It is located at the bottom of the tank. Immediately on the end of the heating element you will see two power terminals, a ground wire and a temperature sensor connector.
First, remove the terminals, grounding and remove the temperature sensor. In order to connect everything correctly after replacement, the location of the wires can be remembered or better photographed.
It remains only to unscrew the fastening in the form of a nut. Take a socket or open-end wrench and unscrew the nut, but not completely. Press the bolt inward so that the heating element can be removed.
Now, with up and down movements, loosen the heating element and carefully pull it out.
Perform tank maintenance. All residues of powder, scale and other debris must be removed. Now we need to replace the heater.
Buy a new heating element, starting from the markings of the old one. Connect the temperature sensor to it and insert on Right place. If there are guides, you need to get into them and stick the device. Tighten the fixing nut, connect the wires, it is important not to confuse them.
The last step is the reassembly of the machine.

Heating element seat

That's all. Ten has been successfully replaced. Since the brand is different, the fasteners can be in different places, but the procedure and principle are the same for everyone.

Check ten

It happens that replacing the heater does not solve the problem, so at the stages of disassembly, you need to check the heater itself. You can check it with an ohmmeter. If the device shows infinite resistance, it burned out. If not, you need to check if everything is in order with the wires, if there are any other damages.

Ten behind

Indesit, Whirlpool and similar models must be dismantled from the rear. This option is much easier and faster.

Dismantling from the rear panel

In this article, we will replace the heating element of a washing machine, commonly called a heating element. This repair is simple and can be done by most non-professionals with normal tools, the average time to complete this repair will not exceed 30 minutes.

Video replacement of TENA on a washing machine:

Replacing the heating element in the washing machine with your own

Before starting repairs, make sure that the washing machine is unplugged. To access internal components washing machine, you must first remove the back panel. Take a screwdriver or a screwdriver to unscrew the bolts holding the back cover. The heater is located at the bottom of the washing machine tank:

To access it, we need to disconnect the phase, zero and ground connectors. There may be a thermistor in the middle of the heating element, in order to disconnect its harness, you must press the latch and pull it out of the socket. If there is a shield on the heating element, then unscrew it:

Now grab the tabs on the heater contacts and pull it towards you, you may need to press the gasket with your finger and move the heating element back and forth to remove it:

Next, we buy a similar heating element for your machine and install it in place. To install it, insert the heater into the socket and press the gasket along the edges until it is installed in the hole. Gently slide the heater up to the tank body. To tighten the gasket, take the nut that was removed from your old water heater and screw it back into place. If there was a thermistor, then we take it from the old heating element and also put it in place. Then we collect everything in the reverse order.

TEN - a part of a washing machine that heats water for washing. It is usually located at the bottom of the tank, and its key “feature” is premature and frequent failure.

Not a single high-quality washing machine, even Bosch or General Electric, is protected from burnout of the heater. To replace a damaged element, you should know how to remove the heater from the washing machine. We will cover this in detail in our instructions.

If you are sure that the water does not heat up during washing (things are not washed, the hatch is cold in the high-temperature mode), then it is the heating element that is to blame for the failure. Although the failure of the temperature sensor is not ruled out.

Before you start repairs and remove the heater and thermostat (which is usually built into the heating element), you should definitely make sure that it is broken. The reasons for the failure can be such factors:

Long service life, frequent use of high temperature conditions.
The formation of scale on the element due to hard water, which leads to the burnout of the part.
Failure of the temperature sensor leads to the fact that the heating element does not heat (in this case, it is enough to change the sensor).
Broken programmer or electronic board blocking heat.

As you can see, factory defects and violation of operating conditions are rare reasons for the failure of an element. More it depends on the quality of the water used for washing.

If you want to protect yourself from such problems in the future, use special tools that block the sedimentation of plaque on the tubular element.

How to get a heating element from washing machines of different brands

To pull the heating element out of the washer, first of all you need to figure out which side it is located in your CMA brand. The most common position is behind the washing machine, typical for brands such as LG, Indesit and Ariston, Ardo, Zanussi, Kandy and Atlant.

If you are the owner of a washing machine of a brand such as Bosch, Samsung or Siemens, then you can only remove the heating element from the front. Consider the procedure for both cases.

If the heater is located behind

Proceed like this:

Turn off the power to the machine, drain the remaining water using the drain filter.
Unscrew the bolts securing the rear panel of the CMA housing.
Under the drum you will see the shank of the heating tube.
Memorize or take a picture of the contacts so as not to reverse the polarity when installing a new part.
Disconnect wiring.
Locate the fixing bolt and unscrew it (located in the center of the shank).
Slightly push the fasteners inward, grab the heating element and pull it towards you. If the part does not reach, use a thin screwdriver to pry the seal.

Important! If you are not sure of a 100% breakdown of the heating element, pull carefully so as not to break off the contacts, in case the part is serviceable and does not require replacement.

Clean the hole in which the part was from debris and scale residues.
Install a new heating element, remembering to connect the sensor to it.
Tighten fasteners.
Connect the contacts, observing the polarity.
To make sure that new element is serviceable and all its connections are tight, test the machine by starting washing one by one at different temperature conditions.
Replace the back cover, the job is over.

If you need to get the heating element in front

The work goes as follows:

Unplug the machine.
Unscrew the top cover fasteners located on the back of the SM and remove the front cover by pulling it towards you and up.
Take out the detergent drawer. Self-tapping screws are hidden behind it, fixing the control panel, which also needs to be removed.
Remove the bezel that hides the debris filter. Usually the panel is held by ordinary plastic latches.
Using a thin screwdriver, pick up the seal collar on the machine door and, having removed the mount, wrap the cuff into the drum.
In order not to accidentally break the wires of the door lock, disconnect the wiring or completely dismantle the UBL.
Unscrew the bolts holding the front wall, and, moving it slightly forward, remove it.

The shank of the heating element will be visible under the tank. Take a photo of your contacts.
Loosen the nut and push the bolt inward.
Take the heating element out of the groove.