home > Computer > Why did search in Windows stop working? Windows Media Player does not work, we will quickly solve the problem! Windows doesn't work

Why did search in Windows stop working? Windows Media Player does not work, we will quickly solve the problem! Windows doesn't work

We will fix errors in Windows 10. But approximately the same will need to be done in Windows XP, 7 and 8. In Windows 7 and later releases, the developers have improved the recovery system for startup problems. In older versions of the system, serious errors often have to be resolved by reinstallation.

Disable peripherals

positive.org

Try to remember what changes you recently made to the system: did you install new devices or switch something. There may be a problem with one of the hardware components. Try disabling:

USB drives.
Card readers.
Printers.
Scanners.
Cameras.
All other external devices.

If this does not help, disconnect the keyboard and mouse: you need to exclude everything possible sources malfunctions.

Also the reason may be internal components, For example RAM. On a desktop PC, you can check the performance of the RAM by connecting the strips one by one.

Check power

takprosto.cc

If the computer does not turn on at all, pay attention to the power cable and sockets. Don't forget the power switch on the back of your desktop computer.

If everything works at this level, but the computer still does not turn on, then most likely the problem is in the power supply, which you are unlikely to be able to fix yourself: you will have to replace it or have it repaired by a specialist.

It is possible that the computer turns on, but only for a short time. This is the same problem with the power supply.

Configure the disk to boot the system

Errors may appear during startup: An operating system wasn’t found. Try disconnecting any drives that don’t contain an operating system. Press Ctrl+Alt+Del to restart or Boot failure. Reboot and Select Proper Boot device or Insert Boot Media in selected Boot device.

IN BIOS settings or UEFI can be installed boot from external device or another logical partition, and not with system disk. You can restore default settings like this:

To restart a computer.
Immediately after restarting, press the system key, for example F2. This may be another key: usually during system boot it can be found at the bottom of the screen with the logo of the laptop or motherboard manufacturer.
In the settings, set the desired disk to the first place in the boot.
Select the Save and Exit option to save your changes.

If the above does not help, you will have to restore the system bootloader. To do this, you will need a bootable USB flash drive or recovery disk with a system of suitable capacity. How to do bootable USB flash drive or disk, read Lifehacker about installing Windows.

Start the system from a flash drive or disk by selecting the desired option in the boot menu. In the Windows installation menu that opens, select “System Restore.”

From the recovery menu, select Troubleshooting → Advanced options → Startup Repair. After this, the system will try to automatically fix the bootloader. In most cases, it solves the problem.

The same can be done manually via the command line, but it is better to select the automatic option so as not to aggravate the situation.

If this method does not help, the problem probably lies in the hardware: the hard drive is damaged.

From the recovery menu, select Troubleshooting → Advanced Options → Command Prompt.

At the command line, you need to enter the following commands one by one: diskpart → list volume (be sure to remember the name of the Windows disk) → exit.

To check the disk for errors and damage, enter the command chkdsk X: /r (where X is the name of the Windows disk). The check usually takes quite a long time, you will have to wait.

Start Windows in Safe Mode

Due to a sudden computer shutdown while installing updates operating system, cleaning from viruses and unnecessary entries in the registry or due to the fault of acceleration utilities Windows operation may be damaged system files. In this case, a “blue screen of death” will appear when the system boots.

Try starting Windows in safe mode without loading drivers and programs in startup. If the computer is running in this mode, you will have to remove the drivers, perform a system rollback, and scan for viruses.

If you have restore points, this problem is quite easy to solve. You just need to roll back to the previous stable configuration.

Reinstall system files

The steps above may not help. Then you'll have to reset Windows settings and reinstall the system while saving the files. Unfortunately, all programs will need to be reinstalled.

In the recovery environment, select Troubleshoot → Reset this PC → Keep my files → Reset.

The system will roll back to the original settings.

Unfortunately, Windows not being able to boot is a problem that occurs without an error message or any other obvious solution. You may experience a black screen immediately upon startup, or your computer may restart itself instead of or even after displaying the Desktop screen.
This most often occurs due to incorrect device drivers, system registry errors, file corruption, and malware.
What to do if Windows won't start? There is no Explorer to delete files, no Internet to find a solution, no Device Manager to disable or enable components, and no solitaire to kill time while you wait for the anti-malware program to download. All you have is this book and the sound of your breathing in the silence. Fortunately, Microsoft has removed the limited Recovery Console that was used in Windows 2000 and XP. It has been replaced by a fully automatic set of tools, which will be discussed later, as well as a fully functional command line.
Startup recovery
When building tools for Windows 7 Startup Recovery, Microsoft took the Apple Computer approach: make everything simple, but in a way that doesn't work in the real world.
Recovery launch is set to Windows default 7 in a separate partition of the disk, but depending on the level of damage you will either be able to get there or not. Read the Using F8 section.
If F8 does not work, then you will have to find the installation Windows disk 7, which you may have already forgotten about.
Insert the installation disc into the drive and turn on the computer. If the “Install Now” window appears, then click on the Restore your computer link located below. If a prompt appears on the screen, select the Use recovery tools option, select the operating system from the list and click Next.
Another option here is called Recover your computer using a system image, and it only applies if you used the Create a System Image tool. Be careful with this tool; you will definitely lose all the information if you choose this option.
The good news is that you can relax in your chair and follow the sign for about twenty minutes. The bad news is you have no other choice.
You may be familiar with the interactive menu of five useful repair tools used in... Windows Vista; don't worry, they are also present in Windows 7, but you need to wait for them. Windows will try to fix the problem for a few minutes without your help, only to then give you the option to start Windows installation again. Click Cancel to continue watching the running black bar; you will be offered later best tools system recovery.
If automated Windows tool helped solve the problem, then consider yourself lucky. IN otherwise The message “Startup Repair cannot restore this computer automatically” will appear asking you to send a message about the problem to Microsoft; but since the Windows system is not running and the network connection is inactive, such a message will not be sent anywhere. Click Cancel to display the long-awaited page with System Restore tools. Here's how these tools work:
Startup recovery
Pressing this button will take you back a step; if you've already gone this far, then this option is useless.
System Restore
This button takes Windows back to multiple restore points. This turns out to be useful if latest installation drivers prevented Windows from starting the system. Depending on how long ago the last system restore point was created, either nothing will happen, or you may go back very far. Worth a try, but don't be surprised if it breaks recently installed application or driver. Pay attention to the section “Back to the past - using restore points and shadow copies.”
Restoring a system image
This operation can be used to clean hard drive and recovery backup copy, made using the Create a system image tool in the Control Panel.
Windows Memory Diagnostics
This button will allow you to check system memory for errors. Unlike all the others, this tool does not change anything on the hard drive, so it can be used at any time.
Command line
Of all the tools listed on this page, this is the one that will save you time. Use this tool to open a window Command line, which will allow you to copy, delete or rename files that may be preventing Windows from loading. These actions are also possible in Safe Mode with Command Line Support.
Using F8
Immediately after the computer starts, but before the Windows logo, press F8 to launch the More Boot Options menu.
If F8 does not help, then your computer may not recognize the Windows installation, and you will need the Startup Repair tool on the Windows installation disk described earlier. If these tools do not work or you do not have original disc, then it's best to disconnect HDD from the computer and connect it to another computer using a special USB tool. And then it will be possible to determine the problem, or - in the worst case - try to restore at least part of your data, as described in the section “Restoring a system after a breakdown.”
From the menu that appears after pressing F8, you can select the following functions:
Computer recovery
When you select this option, you are immediately taken to the System Recovery Options page.
If the Recover your computer option does not appear, it means that your hard drive does not contain hidden section"System Restore" volume of 100 MB. If this partition does not exist, then you will need a Windows 7 installation disc to access the tools.
Safe mode
In that Windows mode operates in a semi-functional state, allowing you to troubleshoot or remove programs or device drivers. If network drivers are not responsible for breaking Windows, use the Safe Mode option with loading network drivers instead of just Safe Mode.
Safe mode with loading network drivers
This is almost the same as Safe Mode, except that Windows loads network drivers. This is very important if you need to access the Internet or transfer files from or to other computers over a network to search for solutions and download anti-malware programs.
Safe Mode with Command Line Support
Instead of loading Windows and the Desktop, you will see a Command Prompt window. It will be similar to the one available from the System Recovery Options window.
Boot option Safe Mode with command line support is good choice if you suspect that starting Windows prevented by recent driver installation. When the Command Prompt window appears, type devmgmt.msc and press Enter to launch Device Manager. Then, in the Device Manager window, find the driver, right-click and disable it. Close Device Manager and restart Windows.
To exit the Command Prompt window and restart Windows, type Exit and press Enter. If after entering the word Exit the Command Prompt window closes, but Windows remains running, press Ctri+Alt+Del, and then press the small arrow located next to the red button at the bottom of the screen. To resolve file errors on your hard drive, see the “Finding disk errors” section.
Load Logging
This option starts Windows in the usual way, except that each download step is recorded in the file ntbtlog.txt, which is located in the \Windows folder. If Windows does not start, then start it by selecting boot logging at least once. Then restart your computer, press F8 again and select one of the Safe Mode options listed earlier. When you log back into Windows, read the entry using Notepad; it is likely that last record The log contains information about the source of the problem.
Enable low resolution video mode
This option starts Windows the normal way, but in VGA mode. It helps detect broken drivers or incorrect settings video hardware, running Windows in the most compatible display mode.
Loading Last Known Good Configuration
This option starts Windows with the configuration of drivers and System Registry settings with which the system booted successfully before. Use this option if recent Registry changes or hardware installations have caused the problem that prevents Windows from starting. Check out the section “Back to the Past - Using Restore Points and Shadow Copies.”
Directory Services Restore Mode
If your computer is a network domain controller, which is strictly speaking not possible in Windows 7, this option disables Active Directory. In other words, you won't be able to use this method on Windows 7.
Debug mode
This mode, which is not typically intended for end users, sends problem fix information to the serial port for recording by another computer. In general, does your computer have a serial port?
Disable automatic reboot in case of system failure
Unlike the other eight options, this one simply changes the settings so you can determine why Windows won't start. If a crash occurs while loading Windows, then by default the computer reboots so quickly that it is impossible to read the error message on this notorious blue screen. Disable automatic reboot on system failure if you want to read the message and then restart your computer manually.
Disable driver signing enforcement
By default, the 64-bit edition of Windows 7 will not allow the installation of any drivers that have not been electronically signed.
It is possible to disable driver signing enforcement to allow the computer to install unsigned drivers, but in practice this never works. Instead, to boot Windows, open a Command Prompt window and type the following:
bcdedit.exe - set loadoptions DDISABLE_INTEGRITY_CHECKS
Press the Enter button, close the Command Prompt window and restart Windows to get the desired result. If this doesn't work, then you may have to drop support certain devices, until the manufacturer makes a signed and “native” driver for them.
The name of this option speaks for itself - use it to continue with the normal loading Windows as if you never pressed F8. With these tools, you'll have everything you need to get Windows up and running again.

Failures and failures in the operation of the standard Windows media player are not at all uncommon. To understand why Media Player does not work, you need to understand the reasons for the program failure. The most common causes of failure are:

Operating room failure Windows systems;
Viruses.

It doesn’t matter what exactly the reason is, it most often leads to the deletion of keys in the registry and Windows libraries. This can happen either due to the fault of the user who installed incorrect or malicious software, or due to a failure Operating system Windows.

As a result, we get a failure to launch and operate the media player, which can be fixed in 3 ways. I would like to immediately note that these solutions for restoring work Windows Media Player are the same for different editions of Windows: Windows XP, Windows 7, Windows 8-8.1 and Windows 10.

I don’t think it’s worth cluttering the article with screenshots from all available Windows, since only the interface changes in the process.

3 ways to restore Windows media player functionality

Since there are different reasons, not each of the solutions presented can correct the performance of the media player. Therefore, perform each of the methods sequentially, checking whether Media Player is working or not.

Restarting media components

The easiest way to solve a problem with a non-working player is to reboot it, so to speak; for this you need to perform a number of simple steps.

Go to the “Start” menu and select the “Control Panel” section

Now we look for the “Programs and Features / Uninstall or change programs” section, go to:

Go to the “Turn Windows features on or off” section

We wait a few seconds for the loading and we see a small window in front of us in which we need to find the line “Components for working with multimedia.” Our task is to uncheck this line and apply the settings. Be careful, you will be asked to restart your computer; this must be done.

After you have applied the new settings and restarted the computer, go back to this menu again and put the checkbox that you unchecked back in place, after which we try to launch Windows media player. If the problem remains, then do not despair, just move on to the next method and everything will definitely work out.

Re-registration of system libraries

The process is quite complex from a technical point of view, but in practice it is very easy to carry out and thousands of users use their player in normal mode within a minute, I wish you good luck too. Our task is to put things in order in the system libraries; to do this, simply click the “Start” menu and enter the command directly in the search bar: regsvr32 jscript.dll

Next we enter two more commands:

regsvr32 vbscript.dll
regsvr32 wmp.dll

It turned out to be three commands, which you applied in turn, the main thing is not to skip more than one, just write it down, apply it, and do the same with the next one and the next one. And when we’re done, we try to turn on our worker windows media player.

As a result? Is the problem resolved? I think that after this, almost all users are happy with the player without problems, but if you are still suffering, because you have some special problem, then it’s time to move on to the “heavy artillery”.

Automatic recovery of Media Playera

At this stage everything is incredibly simple, our task is to go to the official Microsoft support website and find there free utility, which should automatically test a number of problem cases associated with windows player media and eliminate them immediately.

Agree, this is very cool and incredibly simple, the main thing is that it helps. And for this we begin to act.

And now we download the same program onto our computer:

After you have downloaded the utility, simply launch it and follow the clear instructions:

If a user has a problem when Windows 7 does not start on a computer or laptop, then this article will help solve this difficult problem. Starting Windows 7 is sometimes impossible due to errors occurring in the system after hardware problems or incorrect installation software, malicious utilities, etc.

But the most common reason why Windows 7 sometimes won’t load lies in the operating system itself.

Solution

In the case when all the initial stages of launching Windows 7 on a PC or laptop are performed normally, but Windows 7 still does not start completely, this usually confuses novice users. Although if available detailed instructions, the question: “What to do?” will not appear even for beginners. If the problem is caused by hardware failure, then it will be indicated by the signal from the speaker of a laptop or desktop computer during the POST test. If this is the case, then the OS will not start.

But if the problem programmatic and the process stops at the Windows 7 loading stage, which means the user is faced with the most common problem that can be solved using the algorithm of typical actions.

Instructions for action

You must use an OS recovery tool. During the PC startup process, if Windows 7 does not start, the system often recommends that the owner of the computer or laptop select boot options. If for some reason such an offer has not been received, then the user can independently open this menu by clicking on the “F8” button. Then proceed to "Sevens".

What to do if the above instructions did not solve the problem?

To fix the problem when Windows 7 does not start, you need to use a CD with the OS:

Insert the installation disk into the PC drive;
Start the system from the disk (in the BIOS the appropriate order for booting the system from media must be set);
In the window that appears, click on “Apply recovery functions that resolve OS boot problems” and click on “Next”;
Then in the “OS Recovery Options” menu, click on “Startup Repair”;
Wait until the system analysis is completed and the causes of failures are eliminated;
Reboot the PC;
In the BIOS, set the system to start from the hard drive ( When exiting the BIOS, be sure to save the adjustments made);
Restart the computer again;
Ready! Windows 7 will now boot normally.

Using the command line

If for some reason it was not possible to restore Windows using installation disk, then there is another way to do this through the command line.

First, you need to take the steps indicated in the paragraph about restoring normal loading of the “Seven”. The only changes are that simply in the “ ” menu you now need to specify the section “Command Line”.

What to do when you fail to achieve a positive result by following the above instructions?

If success was not achieved and the user has already reached this part of the article, then the problem cannot be classified as a typical failure boot distribution OS. You will need to do all further actions in Windows safe mode. It is recommended to analyze drive “C” for the appearance of broken clusters.

To login " safe mode» you must do the following:

Why are preventive measures important?

Windows 7 has a special system that can make special reference points, with the help of which, if necessary, it is restored. By using this protection function, even a novice user can always easily return the OS to a working state.

For example, in case of failures due to incorrect installation of applications, drivers and other utilities such as codecs, or when errors occur due to adjustments being made to the registry.

It should be noted that in “Seven” it is possible to allocate a fixed amount of memory on the hard drive specifically for such protection of the operating system. Implementation available in Windows 7 self-configuration protect files along with system data, or you can do this separately.

The Windows 10 version has many additional features, including a convenient line search located on the taskbar. A useful option that many users quickly got used to - with its help you can very quickly find required file right in search engine on . However, some may experience Problems with her work, or she may refuse to work at all for some reason.

Most often, this can happen after another systemic updates, or after installing “Ten” using the author’s assembly.

You can, of course, try to restore the system using a restore point and this method will be the most effective, however, not everyone creates these points, therefore, before using such a radical method, we recommend trying the methods of solving the problem discussed below. We will also touch on the version of the Windows 7 system, where similar problems are also possible.

Restarting the Search Service in Windows 7

If you have a Seven, the solution to the problem may be restart service responsible for searching the system.

Let's go along the way Start/ Control Panel/ Administration/ Services. Here in the list we find Windows Search- click Properties.

If the service is disabled, click Launch. The startup type must be set Automatically. If the service is running, try stopping and starting again.

After launch, we check the operation of the search function.

Rebuilding indexes in Windows 7, 10

An effective method of correcting such a failure for both 7 and 10 Windows versions May be rebuilding indexes. Microsoft gives the same recommendation for fixing this bug. To do this, we find point B.

In the Options window, open Additionally.

Click Rebuild In chapter Troubleshooting, after which we confirm this action.

Or, in the indexing options window, click the link when searching and indexing.

The troubleshooting procedure will begin.

Upon completion, you will be asked to select options for the problems noticed. Select the first two among them by checking the boxes and click Next.

After diagnostics and correction, if completed successfully, you will receive a corresponding message indicating the successful completion of automatic error correction. Reboot computer - the problem should be fixed.

Using the Registry Editor on Windows 10

You can try to solve the problem using editing registry keys (parameters). Launch the editor system registry, for example, by entering the word regedit in the window Execute, called by the key combination Win+R.

Using the explorer (represented in the form of a tree structure, similar to the standard system explorer), we look for a branch Windows Search, located on the way: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft