The default router password is dir 615. Possible problems when connecting devices after changing the password or network name

Connecting your home to the Internet is very simple and often even cheap. However, not all Internet companies provide router configuration for you. Therefore, the first user, the buyer, has to independently configure the router.

To avoid any problems in setting up, just follow our simple instructions on D-Link setup DIR-615.

Features and appearance of the router

There is almost nothing to say about the characteristics of the D-Link 615, because for all such devices they are extremely similar to each other. 802.11n technology is used, built-in antennas, 4 network ports, operating frequency is about 2.4 GHz. Data transfer rates up to 100 megabits per second via cable, up to 300 megabits per second via wireless network.

On the front panel there are several, and to be more precise, 8 lights that act as indicators:

• The first indicator is “Power”, this light is responsible for powering the device, connecting to electricity.
• The indicator is labeled "WPS", it shows the status of this function.
• Internet light bulb. It is not difficult to guess what she is responsible for. This is the state of connection to the world wide web.
• The remaining indicators are responsible for the ports. The first one is WLAN. This is wifi mode.
• 4 more connection ports via LAN cables.

There is only one "WPS" button on the sidebar, which can make a quick connection.

On the back panel there are two special places for mounting our device to the wall. And below are the various ports and buttons:

• First there are 4 local ports where you can insert network cable to connect home computer directly.
• One port for internet connection.
• The button is located inside the “Reset” hole. To press it, you need to use some thin object, such as a paper clip. Press this button for 7-10 seconds. After that, the device will be restored to factory settings.
• Router power socket. Here you need to insert the power cord, which the other side should be in the outlet.
• Power on / off key for the router. With this button you can reboot the router.

After we know exactly the location of all the connectors and indicators we need, we can proceed to install the D-Link DIR-615 router, we will configure it a little later.

Installing the router in place

We choose a place that would be approximately in the middle of our house or apartment. This is to ensure that the signal in different rooms is approximately the same. There should be an outlet nearby and the Internet cable should get there.

We attach it to the wall, insert the power supply, turn it on with the power button, connect the laptop or computer to it via the LAN port. Here there is another point that is important in further configuration. If the Internet immediately appeared on the computer, then you can immediately determine what IP address your provider has.

If the Internet immediately appeared, then you have a dynamic IP address. Through the WLAN wire, the provider immediately redirects incoming traffic to you.

There should be no questions about how to connect or how to install a 615 router for Rostelecom, because each connector answers its own wire.

To make a static IP, you need to perform port forwarding D-Link 615. Let's go directly to the D-Link settings. We will write about how to open ports on a D-Link router in a separate article.

Full device setup

To begin with, immediately after connecting the 615s router to the computer, it is worth resetting the settings. So, to set up D-Link DIR-615 from the very beginning:

Reset

To reset the settings, you just need to hold down the "Reset" button located on the back of the device in the hole. Hold down the key for 7-10 seconds. All settings of the D-Link DIR-615 router will become factory settings. This is especially important step for those who bought the device after someone's use.

You can also reset for those who have forgotten the password. To set the default password and login on the router WiFi D-Link. After the reconfiguration is performed.

Firmware issues

After that, it is worth noting that routers usually have old version firmware, the oldest. You can also work with it, but it's better to save your nerves and strength - download the update. Download the most new firmware to keep up with the whole world.

On the underside of our device there is a serial code and a bunch of other information about the update. We are interested in the line "H / W Ver.: **". The asterisks should be the version of your D-Link DIR-615 router. We have K1.

Now, before entering the settings, we go to the official website http://ftp.DLink.ru/pub/Router/, we do everything clearly according to the screenshots. Here is an example of updating K1.

now we have software for our router, which we needed to update. Now, in fact, we will learn how to flash the D-Link DIR-615 router.

To do this, go to the settings on the router debugging site in the router settings, this is the address 192.168.0.1 or 192.168.1.1. Enter the name and password - “admin” - these are the factory settings of router D. Now you can see the interface. Above is the firmware version. If this is version 1.0.0, then go to "Configure manually". Then "System", select "Software Update", select the file that was downloaded a little earlier and update the modem.

This completes the flashing.

Debugging a connection to the WEB

We go into the same router settings at 192.168.0.1, enter admin / admin, click "login". AT updated firmware Click on advanced settings at the bottom. Then select WAN in the list, this item is located in the "Network" block.

Press the "Add" button, thereby creating a new network connection. Here you need to enter the data that the provider provides you. The connection type, login and password must be specified in the contract, do not forget to clarify these points with him. This is required to connect to the Internet. Click "Save".

Internet should now appear local network, that is, on those computers that are connected via local LAN cords.

Debugging a wireless network

In the Wi-Fi section, click on general settings. All this is in the same advanced settings, if anyone has forgotten. Here we click "Enable wireless connection", check the box and save. As you can see, setting up a D-Link DIR-615 Wi-Fi router is a fairly simple task.

After that, in the SSID field, enter the name of your Wi-Fi, it will be visible to everyone. write on English language. We select our country, we leave the channel automatic and the mode is the same.

Now in the Wi-Fi block, select the security settings. In the first paragraph wifi settings set WPA-PSK2. In the next field, where is the encryption key. This is the Wi-Fi password. On the same tab, the answer to the question of how to change the password or how to put a password on Wi-Fi.

Now you have figured out how to set up a D-Link DIR-615 router thanks to our step-by-step instructions.

Related videos

Fast internet to you!

The D-link DIR-615 setup has not yet been described in such detail as this time. In this publication, we will look at how to configure a fairly common D-link DIR-615 router. In the article, I will refer, as an example, to D-link DIR-615/A. But even if you have a router of a different brand, it doesn’t matter, because in many ways the settings for everyone are identical. Therefore, this manual is applicable to most D-link models. I will try to explain everything in detail and in an accessible language.

I will not describe the features of the router itself for a long time, if necessary, you can read about DIR-615 / A if you follow the link located a little higher. I will only note that this model perfectly copes with its functions at home, or in not too large offices. With its help, uninterrupted Internet is supplied to computers, tablets, phones via a wireless connection.

In terms of setting up the D-link DIR-615, it is quite easy to implement. Provided that your Internet provider uses the Dynamic IP connection method, then you just need to connect and turn on the router, and you will be able to access the Internet. You just need to put the secret code on Wi-Fi, and change the name, if necessary. The only thing that does not suit me is that in almost all editions the settings of the D-link parameters, that is, the control panel, are changed (visually). As such, your router settings may not look exactly like what is shown in this post. Although this is fixable, you just need to reflash it.

We act according to the following scheme:

1. We connect the router and enter the D-link DIR-615 settings page.
2. Setting up an Internet connection on the router
3. Set up a wireless network and change the password combination.

Now let's look at each of the stages in more detail.

Connect D-link DIR-615 and go to settings

Turn on the router by first connecting it to a power source. If no lights are on in the foreground, the power button in the back may be turned off. In case the setting D-link DIR-615 will be carried out through a cable, find the power cord, and connect the access point to the computer (the cable is sold as part of the router). Connect one side of the cord to LAN black connector (in the first of the four), and connect the other to network adapter laptop or computer. The Internet cable must be plugged into WAN connector, which is colored yellow.

In the event that a cord is not available, or a computer with network card, you can make settings using wireless network. In this case, even a phone or tablet will do.

Connecting the Router to the Wireless Network for Configuration

Make an Internet connection under the usual name DIR-615

It can be protected. In this case, use the password that is indicated at the bottom of the router

Then you should open the control panel of the router. But first, I recommend resetting all existing settings so that if they are set, they will not fail. Thus, we will configure our router "from scratch".

Reset settings on D-link DIR-615

Resetting the settings is not difficult at all. To do this, take a sharp object and use it to press the button RESET, which is slightly recessed into the system case, and wait a bit. Then stop pressing and wait for the router to reboot.

Log in to any internet login program and navigate to the internet address 192.168.0.1. A window will pop up asking for a username and a secret code. If you did not change this data, then dial admin both lines and the control panel page of your router opens.

It may be that the settings there will be in English, which can be easily changed to a more suitable and understandable one (Russian, Ukrainian).

A window may also pop up, in which it is indicated to change the initial password, which is used to enter the D-link control panel. Then enter any cipher you have thought up and repeat the same on the next line. And be sure to remember, or better write it down, as you will need to enter it every time you enter the router settings.

I recommend that you immediately, before setting up, download the new software to your D-link. You can read in detail how to do this in this article . But you can carry out the configuration further and without firmware, if we assume it will be difficult for you to do this.

After entering the password, we directly went to the settings, now you can configure the router.

The sequence of the Internet setup process on the D-link DIR-615 router

1. First of all, it is necessary find out what connection technology your provider uses. Active IP address, fixed, PPPoE (practiced by Dom.ry, and other Internet providers), L2TP (used by Beeline). In my articles, I told you how to learn connection technology. It is possible to find out this information on the main website of the provider, or even call the company.

Provided that your Internet connection is made using the widely used Dynamic IP technique, the router should distribute the signal as soon as a wire is connected to it from the company that provides the Internet. Then you will just need to make the wireless network settings (we will discuss how to do this later). If you have a static IP address, then you will go through the configuration.

1. Find a tab Start— Click'n'Connect. Recheck your internet cable connection and select Further.
2. From the list that appears, find desired connection. If, for example, your connection is PPPoE, and the Internet provider also gives IP in addition to this, then we make the choice PPPoE + Static IP. Provided that the IP address is not provided, then put the selection icon in front of PPPoE + Dynamic IP. We do the same if the connection is L2TP.
3. Next, specify the data of the IP address, if it is provided to you (otherwise this window will not be there). And you press the button Further.

1. Next, the window "Addresses of local resources of the provider" may open. If you do not know what it is, or you simply do not want to enter additional addresses, then press Further. A window pops up asking for a connection name and user, and entering and confirming a password. This information is provided by your Internet Service Provider. To make more settings, go to the Details tab.

Then a survey of Internet connections and the reality of the connection will be carried out, the selection of Yandex. But that's if you want. However, these settings can be changed.

The settings were considered using the example of PPPoE for the D-link DIR-615 router. Your settings may be different.

If you set up an access point, but as a result there is no Internet, “no access to the Internet” is displayed, or there is no access to the pages, then this problem is related to the settings from the provider company. Double-check, you may have incorrectly indicated the type of connection, or some other data.

Therefore, PPPoE, PPTP, L2TP and Dynamic IP connection is more difficult than the Static IP connection method.

Very important! Provided that you previously accessed the Internet using high-speed data exchange, now you, in fact, do not need it. Such an Internet connection will be made by your router and only distributed over the wire and wireless network.

Change settings from the provider using the same Click'n'Connect, or by going to Net —WAN, while selecting and changing the required connection.

Provided that everything is in order, and the Internet connection through the router is available, then we proceed to setting the wireless network parameters.

An illustrative example of setting up Wi-Fi and changing the password combination on D-link DIR-615

Now we just need to change the name of the wireless network, and come up with another secret code to secure the Wi-Fi connection.

Stand on Wi-Fi - Basic settings. Here you can change the name of our wireless connection. In line SSID enter the name of the network - Internet, and select Apply.

Next, open the menu WiFi — Security Settings, and in the line "PSK Encryption Key" enter the code, then you will use it each time to connect to the Wi-Fi network. The secret password must contain at least 8 characters. Remember, or write it somewhere, so as not to forget later

The settings you have made must be saved. System - Save. This may be the final step in configuring the D-link DIR-615 router. If no settings

will no longer be carried out, then reboot it. System - Restart.

Now the Wi-Fi network is set up. In addition, you may need to see a more detailed article on setting up Wi-Fi.

It is also possible to change the admin password, the use of which is necessary to enter the router settings. To do this, use the tab System - Administrator password.

Enter the code you came up with twice and select the button Apply. Be sure to save your actions.

Remember or record secret code so that you do not have to reset all settings again, since without a password, entering the control panel of the router will not be available.

Hello. We have a D-Link DIR-615 router. We went into the settings with the password and login admin, changed them and forgot. How to be now?

Answer

Hello. The problem is popular. Basically, on the D-Link DIR-615, and other routers, there is only one solution - resetting the router to factory settings. If you have changed and forgotten the password to enter the router settings, then it cannot be restored. I saw some articles on the Internet about this topic. But everything is very difficult there. And the manufacturer has probably already closed all these "holes" a long time ago, since this is the security of the router.

Therefore, in order to enter the settings of the D-Link DIR-615, from which you forgot the password, you will have to reset the router to factory settings. After the reset, the factory password will do: admin.

Important! After resetting the settings, the router will be like new. For the Internet to work, it will need to be reconfigured. It all depends on your ISP. If you are not sure that you can configure the router yourself, then it is better not to reset the settings.

To do a reset, you need to press something sharp on the RESET button, and hold for 10 seconds.

Here detailed instructions to reset settings on D-Link:

The instructions for setting up the D-Link DIR-615 may also come in handy:

D-Link DIR-615 Wireless Router (802.11n, 300 Mbps)

CONNECTING D-Link DIR-615 TO A COMPUTER

• Turn off your computer.
• Connect the D-link DIR-615 device (one of the LAN ports) with a cable to network card computer.

You can also connect to the router via Wi-Fi. To do this, open the list of available Wi-Fi networks on your computer and specify the DIR-615 network.

• Next, connect the power adapter to the device and then to a power outlet.

• Turn on your computer.

SETUP D-link DIR-615

CONNECTING TO THE WEB INTERFACE

1. Open a browser.
2. Enter 192.168.0.1 in the address bar.
3. If the router is set up correctly, you will be prompted to enter a username and password (username and password are admin).

Entering login and password

NOTE: If you see the message "Unable to display the page" when connecting to the web interface of the router, make sure that the router is properly connected to the computer.

• Click the TOOLS tab.
• Then open the ADMIN tab in the left column.
• In the column ADMIN PASSWORD in the field Password enter a new password and repeat it in the field Verify Password: You can use numbers, Latin letters of both cases, as well as symbols available on the keyboard.
• Finally, press the SAVE SETTING button.

NOTE: It is better to write down the new password so as not to forget. If the new password is forgotten or lost, you can restore the factory settings using the RESET button. This action will overwrite all specified settings to factory defaults.

Changing the base password

NETWORK CONNECTION SETUP

IMPORTANT: WAN connections are set up according to the data provided by the ISP.

ESTABLISHING A WAN CONNECTION

Select SETUP from the main menu, then Wireless Settings from the left column. In the window that opens, click on the Manual Wireless Connection Setup button.

Enter the necessary settings:

1. In the WI-FI PROTECTED SETUP section, remove the check mark from the Enable item, since not all wireless adapters support this technology.
2. In the Enable Wireless item, select: Always.
3. In the graph Wireless Network Name enter the name of the wi-fi network.
4. Parameter 802.11 Mode set: Mixed 802.11n, 802.11n and 802.11b.
5. Security Mode: WPA-Personal.
6. In the WPA Mode settings section: WPA-Only.
7. Cipher Type: AES.
8. In the Pre-Shared Key input field, enter a password to protect your wireless network. You can use as a password serial number(S/N) indicated on the back of the box.

After filling in all the parameters, click the Save Settings button. Wi-Fi setup on the D-Link DIR-615 router is over.

CONNECTING IN ROUTER MODE

To configure the router in this mode, go to the section Manual Internet Connection Setup(SETUP - INTERNET - MANUAL INTERNET CONNECTION SETUP button).

First, configure the PPPoE mode on the computer to automatically obtain a local IP address (DHCP), the instructions for your operating system can help with this.

1. In My Internet Connection is select: PPPoE(Username/Password).
2. You must set the selection in the Adress Mode item to dynamic IP.
3. In User Name we write the login specified in the contract.
4. In Password, we drive in the password specified in the agreement + in the Verify Password field - we repeat the password.
5. Reconnect Mode: put a mark on always on, for a permanent connection (recommended).
6. MTU field - 1472 (default 1492).
7. Click the button Clone MAC Address.

PPPoE mode setting

We save the settings by clicking on the Save Settings button - the device will reboot.

SAVING (RESTORING) D-link DIR-615 ROUTER SETTINGS

• To save the current settings, select Save Configuration.
• To restore settings from a file, click Browse, select the settings file, and click Restore Configuration Defaults.
• To restore factory settings, click Restore Device.
• To reboot the router, click Reboot the Device.

it basic settings D-link DIR 615 router. But even after doing them, we will get a fully working Wi-Fi network with Internet access.

Each user is faced with the problem of changing the factory settings of a new router. This post will address the issue of changing the default default password and key wifi connections for router D-link dir 615.

So, to get started with the settings wifi router D-link dir 615, or rather, change access keys, first you need to go to home page device authorization. The web interface of the router is located on standard address, which is written in the address bar of the working browser - http://192.168.0.1.

Change factory password

When purchasing a new device, the first thing that each user needs to do is to change the authorization key without fail. This step is very important, because by setting a reliable access key to the web interface, the paths for fraudulent actions on the part of intruders are blocked. Through the parameters page of the D-link dir 615 router, you can not only find out the right key for wi-fi, but also steal user access information to the services of an Internet provider.

Often, after buying a router, delivery managers change the password in advance to the serial number (S / N) of the access point. This number is always indicated on the factory box and is duplicated on the device's branded label. It is very convenient to use this number as an authorization code, as it is unique, difficult to select, and it is simply impossible to lose it.

To set up a new password, in the interface of the D-link dir 615 router, you need to find and follow the link "Tools". Then open the "Administration (Admin)" section. In the window that opens, there will be special lines in which you need to enter a new password. In the "Password" field, enter new code, and in the line "Verify Password" repeat the characters entered earlier to set them as a new password.

Now that all the keys are entered, all that remains is to save the changed values ​​\u200b\u200bby clicking the "Save Settings" button. Then D-link router dir 615 will reload the options page and prompt you to log in again using the new login options.

How to set a wireless password

Usually, in new devices there is no prohibition on use of wifi networks, which means that neighbors can use it completely free of charge. Everything would be fine, but because of a large number connected devices to the Internet through one access point, the connection speed is noticeably reduced, which means that it is simply necessary to limit the number of connected devices.

To put a new wifi access key, you still need to open the web interface of the D-link dir 615 access point. Find and select the "Setup" section, then click the "Wireless Settings" link in the left column. And in the new window that opens, at the bottom of it, click on the "Manual Wireless Network Setup" button.

It remains only to set the necessary parameters and you can start using wireless private wifi networks.

All settings must be done exactly as shown in the picture above. In the first section “Wi-fi Protected Setup”, it would be better if you uncheck “Enable”, otherwise, problems may arise when working with wireless wi-fi devices, since not all wifi adapters support this technology.

• Set the checkbox "Enable Wireless", "Always".
• In the column "Wireless Network name" indicate the name of the new wi-fi network.
• Security mode: "WPA-Personal"
• WPA mode: "WPA-Only"
• Cipher type: "AES"
• Pre-Shared Key: here you need to put the same key for accessing wi-fi, for which all these settings were made.

As already mentioned at the beginning of the article, you must use the serial number so as not to lose the access key, so we look for the S / N number on the back of the wifi device, and then we need to put it as an access code.

After all the necessary values ​​have been changed, all new parameters must be saved by pressing the "Save Settings" button. After that, the D-link dir 615 router will reboot, and you can get to work.