Wi-Fi d link works. How to set up a D-Link Wi-Fi router: step-by-step instructions
The D-Link DIR-300 router has a point on board Wi-Fi access 802.11n and allows you to organize your home wireless network, through which mobile gadgets will be able to access the Internet and access each other’s files. Correct setting router not only helps to avoid hacking home network“craftsmen”, but also allows you to significantly increase the Wi-Fi speed and increase the coverage area of the D-Link DIR-300.
After connecting the D-Link DIR-300 router to the provider’s network, you can configure Wi-Fi, set a password and distribute the Internet to wireless devices. The access point can be configured in three ways:
- Using the “Wireless Network Setup Wizard”;
- Manual setting of parameters;
- Automatically, via WPS protocol.
Quick setup
The DIR-300 provides configuration using the “Wizard”. This method requires minimal effort and allows you to set up a Wi-Fi network in seconds without diving into technical details.
To establish a connection, you need to log into the router’s web interface and select the “Wireless Network Setup Wizard” section. Depending on the firmware, the “Wizard” may be located in different places in the interface, but all options and menu items are in different versions The software have the same name. Procedure for the “Master”:
Set the network mode to “Access Point”.
Enter the access point name - the name of the Wi-Fi network, which will be displayed on all connected devices. For security reasons, it is not recommended to leave the default name “DIR-300”.
Select the “Secure Network” item and create a password that the router will request from connected devices.
After completing these simple steps and applying the changes, the Wi-Fi setup using the “Wizard” will be completed and the D-Link DIR-300 will be completely ready for use.
Manual setting
Unlike quick setup, manual configuration allows you to take into account the characteristics of connected devices and neighboring networks, which allows you to improve throughput and reception quality.
Basic manual setting Wi-Fi networks for home use on DIR-300 it is performed in 2 stages:
- Setting basic network parameters;
- Configure security settings.
basic settings
The main wireless network parameters are located in the router control panel on the “Wi-Fi – Basic Settings” tab. To go to this item in the “dark gray” interface, you will need to switch to advanced mode.
Description of functions:
- The “Enable Wireless Connection” option controls the access point’s power. In order for devices to use a WiFi connection, the checkbox must be checked.
- Disabling Wi-Fi network broadcasting without deactivating the radio module may be necessary when using the DIR-300 in client mode. If you remove this checkbox from standard mode, That wireless connection between the router and all devices will be interrupted.
- The MBSSID and BSSID parameters are configured when the router is used to simultaneously serve several wireless networks. At home, such a scenario is unlikely, and if there is only one network, these parameters cannot be changed.
- If you check the “Hide access point” checkbox, the WiFi network name will no longer be displayed both on other people’s devices and on trusted ones. In this case, the router will not stop broadcasting. To establish a new client connection, you will need to enter the SSID manually. This function implemented in D-Link DIR-300 to ensure security.
- Channel selection can be entrusted to the router firmware, leaving the value “auto”, but automatic setting is not always adequate, which often leads to a drop in the wireless speed of the router. To manually select the correct channel, you need to evaluate the performance of neighboring Wi-Fi networks. In the “light” air interface of the D-Link DIR-300, when selected, a histogram appears showing the channel load.
The less loaded the channel, the higher the throughput, and therefore the wireless transmission speed. To study the situation in more detail, you can use one of free programs, for example, WiFi-Analyzer.
Security Settings
Professional hackers are hunting for corporate secrets and are unlikely to be interested in hacking into someone's home access point. But there are amateurs who can “harmlessly” pick up a password in order to use the “free” Internet or connect to the webcam of someone else’s computer. Therefore, you should not neglect basic safety rules.
Wireless network security settings are located in the router control panel on the “WiFi – Security Settings” tab. To go to this item in the “dark gray” interface, you will need to switch to advanced mode.
Description of functions:
- A network authentication method that excludes the objective possibility of hacking - WPA2. In corporate Wi-Fi networks, access is used through a RADIUS server, and for a home network, a preset PSK password key is suitable. Thus, WPA2-PSK mode will provide maximum protection.
- The encryption key is the same password that must be entered on the WiFi device in order to connect to the D-Link DIR-300. Complex password And correct setting– the most important conditions for network security. The password cannot be set to simple numeric or dictionary combinations, or your date of birth. Good password contains more than 8 characters: numbers, special characters and letters, case sensitive. Regardless of the complexity, finding a key is only a matter of time, so it is recommended to change the password to a new one every month.
- AES – data encryption technology. Provides key cryptographic strength without reducing speed wireless transmission, therefore well suited for use in the 802.11n standard. The update period should be left at its default value of 3600 seconds.
- Pre-authentication through adjacent access points is only used in complex networks with multiple routers.
After completing these steps and applying the changes, setup Wi-Fi protection will be completed and the D-Link D-300 will be ready for safe operation.
Connecting using WPS
The WPS protocol was developed to simplify Wi-Fi network setup. For the user, the essence of the technology is that the router is paired with any WPS-compatible TV, smartphone or tablet without having to enter a password: when you press a button on the router, the devices exchange a digital access code and connect automatically.
Depending on the hardware revision of the router, the button may be located on the side or back of the case.
Brief instructions for connecting to D-Link DIR-300 via WPS using an Android device as an example:
Select the “WPS Button” option.
Press the WPS button on the DIR-300 case.
After a few seconds, a successful connection message will appear.
Thus, in just 4 simple steps You can connect any WPS-compatible device to the router and you won’t need to enter any password.
Despite the convenience this method pairing, the WPS protocol has the lowest security: when exchanging identification packets between devices, a digital code is used that can easily be picked up by spyware.
Additional features
- The MAC filter in the D-Link DIR-300 is an auxiliary means of protecting against unauthorized Wi-Fi connections. Allows you to configure both black and whitelists MAC addresses.
- “List of WiFi clients” displays up-to-date information about connected devices. The function allows you to forcefully disconnect any user from your home network.
- The “WPS” tab provides access to simplified device pairing options.
- On the " Additional settings“You need to pay attention to 2 important parameters: “TX power” and “Channel width”.
Transmitter power is expressed as a percentage. The higher it is, the wider the Wi-Fi network coverage area.
The channel width can be selected automatically - 20/40, or adjusted manually. The wider the channel, the greater the throughput, i.e. speed.
The 40 MHz channel gives a noticeable increase in speed, but is less resistant to interference from neighboring networks than 20 MHz. In addition, as you approach the edge of the coverage area, the throughput of the 40 MHz channel is greatly reduced. To improve reception, you will need to configure the D-Link DIR-300 transmitter to maximum power, but then the router will begin to emit too much radio waves, which will “clog” weak waves from the antennas of mobile gadgets. This will significantly reduce wireless transmission speeds on devices operating in close proximity to the router. Thus, it is possible to select the optimal values of power and channel width only by measuring the speed and coverage directly at the installation site of the DIR-300.
- It is not recommended for users who do not have special knowledge to change the values of the remaining parameters on the “Advanced Settings” tab.
- WMM – WiFi-Multimedia technology optimizes wireless traffic for multimedia applications. To improve speed performance while watching online videos or calling on Skype, the option must be enabled. It is not recommended to change parameter values.
- In “Client” mode, DIR-300 can connect to another router to organize complex infrastructure in large homes or offices, as well as when connected to a provider’s Wi-Fi network.
Found a typo? Select the text and press Ctrl + Enter
depositphotos
But to enjoy these delights of civilization you need to know how to set up Wi-Fi router. So, read the detailed instructions about Wi-Fi settings in the apartment. For example, let’s take a very popular in our country D-Link router.
Before starting setup, the router must already be connected to power, to the Internet line, and also to a 220V outlet.
First you need to check that the settings in the network connection settings are correct. If you have Windows XP, then look for the settings in the “Start - Control Panel - Network connections- Connection via local network».
Then right-click on the connection and click on “Properties”. Next, you need to select “Internet Protocol (TCP/IP)” and click on “Properties”.
comp-profi.com
Set the radio buttons to “Obtain an IP address automatically” and “Obtain a DNS server address automatically” and click “OK”.
comp-profi.com
If you have Windows 7. The sequence is as follows. First, go to the Start panel and enter “View network connections” in the search bar.
We find a local network connection and go to its properties. Next we find Internet Protocol version 4.
In the protocol properties, you need to check the “Obtain an IP address automatically” and “Obtain DNS server address automatically” checkboxes. Next "OK".
The next step is to log into the router itself. You launch any Internet browser, and write the router’s IP address in the address bar. It is written in the passport for the router. So, for a D-Link router this is http://192.168.0.1
comp-profi.com
The default router login is admin. Leave the password space blank.
It happens that authorization does not occur. This means that the login and password have already been changed. To reset all settings, you need to hold down the RESET button on the back panel of the router with a match for 5 seconds. After these steps, repeat the authorization again.
Then check with your provider what type of connection should be created in the router settings. Also find out which server, login and password you need to specify. You need to ask your ISP if they need to dictate the router's MAC address. If necessary, dictate it. You can find the MAC address in the documentation for the router.
To do this, go to the SETUP tab, and then to the Internet Setup subsection. You need to click on Manual Internet Connection Setup.
comp-profi.com
Then you choose the type of connection, which you should also check with your provider. It is selected in the My Internet Connection Is item. Next, enter your username, password and other settings. Then click Save Settings.
Today there are hundreds of different routers on the market that allow you to organize your own Wi-Fi network at home. The D-Link company occupies one of the leading places in the list of manufacturers of this kind of devices. It produces a lot of different routers, among which the D LINK DIR 300 model occupies a special place. It combines optimal price and functionality, for which it has received recognition among users. D LINK DIR 300 routers are often purchased for offices, homes, cottages and various other premises where a high-quality Wi-Fi signal is needed. In this article we will look at how to configure the D LINK DIR 300 router.
How to connect the D LINK DIR 300 router
Before proceeding directly to setting up the router, you need to connect it. To do this you will need to do the following:
How to configure the D LINK DIR 300 router
After connecting the router, you can proceed to configure it. First you need to create a wireless network:
At this point, you can consider the local network setup stage complete; now you should go directly to setting up the D LINK DIR 300 router. Any router can be configured via a browser. Follow these steps:
That's all, the setup of the D LINK DIR 300 router is complete. After these steps, the Internet should start working. But most likely you want to configure wireless Internet, this will require you to follow a few more steps described below.
How to set up a Wi-Fi access point in the D LINK DIR 300 router
If you have correctly configured the Internet itself according to the instructions described above, you now need to activate the Wi-Fi access point. This is required to be able to connect to the router from any devices via a wireless connection. This is done as follows:
How to connect via Wi-Fi to a D LINK DIR 300 router
The last step is very simple - connect to the router via Wi-Fi. The connection method is no different from connecting to any other wireless access point. If your computer has Wi-Fi adapter, just turn on the wireless network connection, after which a corresponding icon will appear in the lower right corner, indicating that it is possible to connect to the Internet via Wi-Fi. Click on this icon and select the D LINK DIR 300 access point, identifying it by the name you specified as part of the setup.
Enter the password you specified earlier and connect to the network.
Please note: IfWi-The Fi adapter on your computer is “external”, connected viaUSB, the connection process may vary slightly. Most likely, the connection will occur after installing specialized drivers through the appropriate utility.
Hello! In this article we will connect the D-link DIR-615 router. I will show this model as an example, but the instructions are suitable for all D-link routers: DIR-300, DIR-320, etc. Let’s look at the process of connecting the router. Let's connect power, internet, and computer via cable or wireless Wi-Fi networks. I will provide links to instructions for entering the router settings and setting up Wi-Fi, Internet, etc. Simply put, you can connect and configure a new D-link router yourself.
This is what the D-link DIR-615 router looks like when you just bought it:
You may have a different model, it doesn't matter. The main thing is that we need to connect it all correctly. If you connect it incorrectly, you will hardly be able to configure the router, let alone use it.
We need:
- Connect power to the router
- If the indicators do not light up, turn on the power using the button on the device
- Connect your computer, tablet, phone to the router. Can be done via cable or Wi-Fi
- Connect the Internet to the D-link router. Cable from an Internet provider, or from an ADSL modem
- Go to the settings of our router and configure it.
Let's look at everything in more detail.
Connecting a D-link router to a computer and provider
First, take the power adapter and connect it to your router. Then, plug it into a power outlet. If the router does not turn on, then turn on the power using the button on the router itself. Next, if you want to connect the router to a computer or laptop via a network cable (it’s best to configure via cable), then take network cable, which comes with the router, and use it to connect a laptop or computer. We connect one end of the cable to the network connector on the computer, and the second connector to the LAN connector on the router. On D-link routers, LAN connectors are usually black. They are signed LAN. Like this:
You can also connect via Wi-Fi network. Just turn on the router and a new Wi-Fi network will appear that you can connect to. You may find it useful to connect your laptop to a wireless network.
If you have connected your computer to the router, and you see the connection status on the computer: “Without Internet access”, or “Limited” and the Internet does not work, then this is normal, because we have not even connected the Internet to our D-link and have not configured it yet .
Connecting the Internet to D-link
Most likely, you just have a cable from your provider or an ADSL modem in your house. In the first case, we take a cable from the Internet provider and connect it to the WAN connector of the router. It is on D-link DIR-615 - yellow color. If you have Internet via a modem, then we also connect the cable from the modem to the WAN connector on the router.
Most likely, even after connecting the Internet cable, the Internet on the computer (or other device you connected) won't work. This is because you need to configure the router to work with your Internet provider. I wrote about this in the article: .
You need to go to the router settings, here, and configure it. If you have connected everything correctly, but cannot enter the settings, then look at the article. The main thing is that you need to choose the right connection type and set the necessary parameters that your Internet provider uses. Then the Internet through the router will start working. Also, set up a wireless network, and .
It is best to configure the router according to detailed instructions. We have one like this. But, using her example, you can configure other D-link routers. Look, perhaps I have already added detailed articles on other models. See the section Setting up a router - D-link, or ask in the comments.
In this article we will configure the very popular D-link DIR-615 router. I will write the article using an example. And if you have a different model, then it’s okay, almost everything is the same. These instructions are suitable for many D-link routers. I will try to write about everything in detail and clear language. I won’t talk much about the router itself, read my review and another useful information about DIR-615/A, you can follow the link above. Let me just say that this router is well suited for a home or small office. It will easily provide stable Internet access for your computers, phones, tablets (via Wi-Fi) and other devices.
Concerning D-link settings DIR-615, then everything is very simple there. And if your provider uses Dynamic IP connection technology, then you just need to connect the router, and the Internet will already be working. You will only need to set a password for the Wi-Fi network and change the network name if necessary. The only thing I don’t like is that the settings in D-link change (in appearance) in almost every version. I will enter the router control panel. And therefore, the settings of your router may differ from those that you see in this article. But a firmware update may fix this.
We will configure D-link DIR-615 according to this scheme:
- Connecting and logging into the control panel on D-link DIR-615
- Setting up the Internet on D-link DIR-615 (connections to provider)
- Setting up a Wi-Fi network and changing the password
And now, about everything in more detail.
Connect D-link DIR-615 and go to settings
Connect power to the router and turn it on. If the indicators on the front panel of the router do not light up, check whether the power is turned on with the button on the rear panel. If you will be setting up the router via cable, then take the network cable that comes with the kit and connect the router to the computer. Connect one end of the cable to black LAN connector (in 1 of 4), and connect the other end to the network card of your computer (laptop). Connect the cable from your Internet provider to yellow WAN connector
If you don't have a computer with network card, or there is no cable, then you can configure everything via Wi-Fi. You can even do it from your phone or tablet.
You can also change the administrator password, which is used to access the router settings. If you haven’t changed it, or have changed it but have already forgotten, then you can do this on the tab System - Administrator password.
Enter your new password twice and click Apply. Don't forget to save your settings.
Be sure to write down this password somewhere. If you forget it, you will not be able to access the control panel and will have to reset the settings.
Afterword
Phew, I'm tired :) I won't write anything more. If you have any questions about the article, ask in the comments. I hope you were able to configure your router.
