Tricolor tv service is not available samsung lcd. Work with the access module CAM CI Plus "Tricolor TV", channel tuning, software update
class="eliadunit">
If your TV supports CAM modules, then you can watch paid satellite TV on it, such as Tricolor TV, NTV Plus, TELECARD, Raduga TV, etc. You just need to purchase a smart card from the operator you need , module for this card, and insert the card with the module into the TV's CI slot.
When choosing such a TV, the main thing is not to confuse it with DVB-T2, even if you tell the seller that you want a TV with a built-in receiver, it can sell you instead of DVB-S2, DVB-T2, and these are completely different things. Usually, by the name of the model, you can read what kind of receiver is installed on the TV. For example, in "LG" in the model name "47LM580S-ZA" the letter "S" indicates that the TV has a built-in DVB-S / S2 receiver.
The surest way to determine if the TV has a satellite receiver is to look back, where all the connectors are located, and find the LNB IN antenna input.
All such TVs have a "CI" slot for "CAM" modules. The "CAM" module is selected depending on the encoding in which the content is encoded, for example, if it is "Tricolor TV", then the "DRECrypt" module is needed, and preferably the latest version. There are no problems with the module, it can be easily purchased in a special store.
Brief instructions for setting up the CAM module "Tricolor TV" or "NTV PLUS" on LG TVs.
1. Install the Tricolor TV access smart card into the Tricolor TV conditional access module (CAM WEST CI+). Chip to the thick side of the module.
2. We install the conditional access module in the switched off TV.
3. Turn on the TV and watch information about the module and access card, if there is no information or error code 17, check the installation is correct and go through the equipment registration on the Tricolor website.
4. In the TV menu, in the settings, select the type of antenna " satellite". In the settings of the Tricolor satellite antenna converter, specify the satellite Eutelsat 36A/36B. converter type single. Converter power supply (LNB) - on. LNB 10750. transponder frequency - 12226 MHz or 12111 MHz or 11881 MHz (settings are by default) the flow rate is 27500. We look at the signal quality.
5. Go to channel setting and turn on automatic search(in new generation TVs) transponder frequencies from 11881 to 12418 will be registered automatically. At the same time, it is desirable that the TV be flashed with the latest software version, in this case the Tricolor TV CI + CAM module will work more correctly, all transponders will be up-to-date, and you will correctly scan the desired channels.
6. If everything went well and the channels were found, go to the sound settings on the TV and set it in the " Digital TV sound settings" parameter MPEG. This is done so that the sound on the channels does not disappear when viewing. Go to module settings CI data (CAM) orCI Options > Settings and select " Reset to factory settings". Turn off the TV completely.
9. An important feature LG TVs is a function of "Automatic channel update". It must be turned off in otherwise The TV will periodically reset the channel list you have configured.Go to settings"Channel Auto Update"and set the parameter:off.Now you can fully enjoy the possibilities of your TV, watching high definition channels. Enjoy watching and bright emotions!
NOTE:
Problems with sound or incorrect switching of Tricolor TV channels on the CAM module were fixed in the CAM module update in December 2014.
For self update using the CAM module on the TV, find the service channel in the list of channels of the Tricolor TV operator to update by - " Telemaster".It usually goes under the number333 according to the operator's list. If it is not in the list, scan the channels again.
After you switch to it, you can update the CAM of the Tricolor TV module via the TV menu CI data (CAM) or CI Options > Settings > Download software>OK. If new software is available and you are prompted to upgrade, click the button OK on the remote control after which the software update percentage will go. It is necessary to wait for the complete download of the module software from the satellite and, after the update is completed, reset the module to factory settings: CI data (CAM) orCI parameters > Settings > Reset to factory settings > OK
After the update, everything works correctly, no glitches are observed, all channels are always in place and with sound. CHECKED!
Also on the menu CI data (CAM) orCI Settings > Information > Smart Card > Providers > Tricolor TV You can view information about packages and their expiration dates.
Subscription class breakdown:
Also on the menu CI data (CAM) orCI Settings > Information > Smart Card > General Information you can find out ID numberTricolor TV smart cards for extending and connecting various TV channel packages.
If, after changing the frequencies by the Tricolor TV operator, channels are not scanned on your TV, or the number of channels after scanning is less than 100, do the following: (Thanks to user Dim)
The problem was the same as everyone else. 70 channels, random numbering, etc. etc.
CAM-Module software - up-to-date, TV software (let's say LG MT24) - latest version. Nothing has changed since the software update.
Reset the TV to factory settings. In the settings of the satellite dish and channels, we set the Satellite for Tricolor and NTV + - "Eutelsat 36b" or "Express-AMU1" or "Express-AT1" at position 36 ° E.
In the settings, you can also create a new satellite with the necessary parameters yourself:
Converter Type: Single/Single
LNB Power (ON)
Just add one Transponder/Frequency Tricolor TV: 12111MHz or 11881MHz Horizontal 27500
The most basic thing is to select one of the transponders Tricolor TV 12111MHz or 11881MHz from the list of transponders Polarization-H (Horizontal) Flow rate 27500.
Then choose Manual search, select the home transponder for the Tricolor (12111 or 11881) and be sure to check the box Search network / NIT. Click update and wait for a while. All channels must be registered in normal numbering. All the best.
Channels can be configured in several ways:
You can use the operator's channel setting, for this you need to go to the parameters (settings) of the CAM CI module in the menu of your TV. Select “Update channel list” and then follow the prompts on the screen. Sometimes the TV itself may suggest using an operator profile to tune channels. Thanks to such a search, we will get a branded sorting of channels - News, Cinema, Sports, All, etc.
Or use manual channel search (on some models, this is the only way to tune channels).
For us, there should be a number - 10750 in the upper and lower ranges (sometimes there is only one line in the settings). Also check the name of the satellite - Eutelsat 36/Express-AMU.
Now you can start searching for channels, consider an example on an LG TV.
We go to the “Manual setting” item (sometimes this item is inactive, then you need to start auto-search and immediately stop it). Select the transponder frequency (if it is not there, then you just need to create it). Frequency - 11881 and start the search.
Now the same frequency, but with the “Network search” checkbox active. So our TV will find all the channels.
On Samsung TVs, you first need to delete channels by following this path:
“Menu” - “Broadcast” - “Change Channel”, then in the window that opens in the lower left corner, select “Select All” and then “Delete”. After we need to return to the “Broadcast” submenu and select “Channel settings” - “Manual setup”.
On Sony TVs, transponder search and editing can be done through auto search in the following way:
“Home” - “Settings” - “Digital Configuration” - “Auto Satellite”. The item “Antenna Configuration” should read “Fixed Antenna”.
We continue:
“Next” - “Reinstall satellite settings” - then repeat - “Digital configuration” - “Satellite auto-tuning” - “Antenna configuration” - “Next” - “Select scan type” (we need “Network scan”, “All” channels, “All stations”)
We continue:
“Next” - “Satellite 1” - “LNB configuration (low and high bands - 10750).
After you need to go back using the “Back / Return” button and go to the “Transponder” item where we can set the frequency to 11881.
Then go back two times using the “Back / Return” button and press “start”.
Setting up and connecting the Cam-module
Tricolor TV
Nowadays, many modern TVs are equipped with a built-in satellite tuner and a connector for a Cam-module, which allows you to view TV channels of satellite operators. To watch channels satellite operator Tricolor TV, it is desirable that your TV supports HD AVC (MPEG-4 H.264) broadcasting standards, which will allow you to view programs in both high quality HD, so in SD formats.
To connect the Tricolor TV Cam-module to a TV, you need to purchase the following equipment:
1. Cam-module Tricolor TV;
2. Smart card (comes with Cam-module and one year subscription);
3. Satellite dish;
4. Converter of circular polarization;
5. RG-6 cable (or equivalent) for connecting a satellite dish to a TV.
Next, you need to install and configure satellite dish to the broadcasting programs of the satellite operator Tricolor TV (Eutelsat W4 / W7 36.0`E) and using television cable and F-connectors connect to the plug of your TV marked "SATTELITE".
You can set up a satellite dish yourself, but for high-quality broadcasting it is better to contact specialists.
We perform subsequent work on setting up the Tricolor TV Cam-module directly with the TV:
1. Insert the smart card into the Cam-module until it stops (according to the instructions on the sticker);
2. Insert the module into the TV connector;
The first two points are performed with the TV turned off from the power !!!
3. Use the remote control to reset the TV to factory settings. To do this, press the button - “menu” and select: - “support” - “self-diagnosis” - “reset”, press the “OK” button, after which the TV will reboot;
4. After the reboot is completed, press the "menu" button, then select the menu item "channel" --- "antenna" and select the "satellite" submenu.
5. In the “channel” menu, go down to the submenu “ satellite system"and click" OK ";
6. A window will appear asking for a PIN code, where we enter the values \u200b\u200b- 0000 (by default), a list of satellites will appear, where you need to uncheck all the checkboxes opposite the list of satellites, except for the satellite with the designation - Eutelsat W4 / W7 36E (if you cannot uncheck the marked satellites: we pull out the module from the TV and reset the TV settings again);
7. We go to the "satellite selection" menu and select the satellite - Eutelsat W4 / W7 36E.
And in the LNB settings, specify the following data:
Transponder - 12226 H
Lower gen. LNB - 0
top gen. LNB - 10750;
8. Then go to the "manual settings" menu, look for the transponder 12226 H and press the "search" button;
9. After scanning the satellite channels of Tricolor TV, press the "save" button.
This completes the setup of the CAM - Tricolor TV module, enjoy watching TV!!!
This material is reviewed on a TV brand - Samsung, connection and Cam setup- the Tricolor TV module on TV models from other manufacturers is carried out in a similar way.
How to set up Tricolor on a Samsung TV? Before performing such an operation, let's go through the instructions for hardware connection of devices:
- connect satellite dish to TV:
- directly connect the antenna through the "Satellite" jack. In this scenario, home appliances will be able to automatically pick up the digital information supplied by the antenna. The final picture is displayed;
- antenna connection via satellite receiver- working method in the absence of the above connector. Here, the receiver is already responsible for receiving and broadcasting the signal to the screen. By appearance it resembles an ordinary video recorder.
- start searching for TV programs, but more on that later - first, consider the algorithm for resetting the settings to the standard ones set by the manufacturer.
Restarting the configuration is useful when the user independently performed actions to configure the mode of use of the equipment. We go to the support section, then we go through the following hierarchy of folders and items:
- "Self-diagnosis";
- "Reset";
- specify the PIN-code (standardly there are four zeros in this field);
- confirm intention to cancel set parameters connections.
Please note that in the current step you do not need to attach the Cam module.
Setting up the CI module on a Samsung TV
How to set up the Tricolor Kam module on Samsung TV:
| 11727 L | 11958 L | 12226 L |
| 11747R | 11996 L | 12303 L |
| 11766L | 12034 L (4K) | 12360 R |
| 11804 L | 12073L | 12380 L |
| 11843 L | 12111 L | 12418 L |
| 11881 L | 12149 L | 12456 L |
| 11919 L | 12169R | 12476R |
| 12190L |
- the "Tricolor" network will be displayed - click on "Search", and then - on "OK".
After the steps taken, you have set up a set of digital TV channels for viewing. Then you need to repeat the same manipulations for all 22 transponders - you get 289 channels, taking into account the radio transmission. After installation Cam module the section "General interface" is activated and access to the found channels is opened.
Automatic setting
How to set up the Tricolor Kam module on Samsung TV using automatic search TV shows:
- go to the "Broadcast" tab of the device's menu;
- select "Auto-tuning";
- then you need to click "Start" in the pop-up window called "Auto-configuration";
- select the line "Satellite dish" from the drop-down list;
- mark the type of channels that you intend to find by automated means (TV, radio or all mixed);
- check the box next to the name of the satellite;
When the name of the correct satellite could not be found in the catalog, resort to manual tuning.
- write down the information in the frame called "LNB Settings", specifying it with the operator providing satellite communications;
- make sure the signal strength is between 80 and 100 percent. When the broadcast does not reach 80%:
- deactivate "Tone - 22KHz";
- make sure the antenna is connected correctly;
- be prepared for the possibility of interference when broadcasting TV programs;
- click on "Scan";
- wait for the technician to find available channels;
- click "Close";
- close the configuration menu directly.
Conclusion
We figured out how to set up the tricolor Kam module on Samsung TV. Now we will give a number of warnings, the implementation of which will help to avoid errors in setting up the equipment:
- the procedure for integrating the module takes place in accordance with a specific hardware. This means that you will need to read the instruction manual for the TV model;
- CI setup is completed with an upgrade of activation keys. The upgrade request is made on the Samsung resource in a pre-created account.
Return to the default configuration if something went wrong during the setup process and it was not possible to save the channel list!
Modern TVs do not need to connect additional equipment for a long time and are able to receive and process a signal from a satellite without connecting a receiver. Now to watch satellite television, it is enough to purchase the ci module offered by Tricolor.
This device allows you not to pile up the space of the apartment with unnecessary appliances, leaving it as spacious and elegant as possible. At the same time, the quality of broadcasts remains at the highest level, even when it comes to channels in Ultra HD. As a result, users get maximum benefit from all possible sides. And the only drawback of such devices is an unusual setting that can cause difficulties for unprepared subscribers.
What is a Cam Module
Those who have not yet encountered Tricolor TV modules should know that given device are a portable analogue of standard receivers, designed specifically for smart TVs.
They are a small plate into which a smart card is inserted. It is this device that receives the signal from the satellite and decodes it to watch TV channels.
At the same time, those wishing to buy a cam module will have to think in advance whether the TV they are using is compatible with the new device. Additionally, it should be clarified whether signal reception is supported in the subscriber's region of residence. This information can be provided by official distributors of equipment or consultants. contact center.
General information about setting up the Tricolor TV cam-module
Those who decide to do self-tuning you must know that, as is the case with most similar equipment, there are both universal devices and Tricolor cam modules that can receive a signal from only the mentioned provider. Professionals recommend purchasing equipment of the second type, since it is much easier to set up.
Additionally, you need to be aware of the differences associated with TV models. The procedure for connecting to satellite TV on LG and Samsung TVs has several differences that need to be considered. Further about them will be discussed in more detail.
Setting up the Tricolor ci module on a Samsung TV
Most of modern technology capable of setting up automatic mode. If it does not start, you will have to manually configure the Tricolor with the ci module for the Samsung TV. For this you will need:
- select the User Sat1 satellite on the start page;
- then, in the LNB section, you will need to set the lower frequency limit, which must match the upper one;
- after which the user will have to switch to "channel settings";
- re-specify the satellite and click the “create” item in the “transponder” line;
- then you will need to specify the frequencies and speed (they are present on the website of the satellite company and in the instructions for the module);
- having saved the specified parameters, the subscriber will have to start the search.
For getting complete list later you will have to start the search again. This completes the Samsung smart TV setup, and viewers get the opportunity to watch TV channels.
Setting up the ci Tricolor module on an LG TV
Preparing for the operation of the Tricolor TV conditional access module on LG will be a little easier. Those wishing to watch satellite TV will have to:
- on the start page, set the basic parameters, indicating the type of antenna (satellite), converter (single), satellite (Eutelsat), frequency 12226, power supply (on);
- after saving the listed parameters, the user will be prompted to check the signal level (the reception quality should exceed 80%);
- the next step is to switch to the TV channel search section and start it automatically;
- then it remains to press the save button and adjust the sound in the appropriate subsection (should be MPEG4);
- The last step is to switch to start page and entering an activation code.
Sometimes, before entering the code, you need to reset the settings to the factory level. Otherwise, the equipment is ready for work and subscribers can already watch their favorite programs.
Problems and solutions
Despite the simplicity of preparing the Tricolor Ultra HD cam module for operation, some users are able to encounter sudden problems. They are usually caused by:
- incorrectly inserted smart card;
- equipment failure;
- user errors;
- incorrectly rotated antenna (the reception quality scale on the screen will be below 80%);
- non-compliance of the TV with modern requirements.
Clients of a satellite company are able to cope with almost every of these troubles on their own. So, it is often enough to check the connection and carry out the setup procedure again.
Sometimes you need to go to the module menu and reset the settings to the factory level.
In the most difficult situations, you will have to call the contact center consultants. But it is important to prepare information in advance that will allow them to recognize the caller. It includes passport data, connection address, service agreement number, smart card ID.
